- Limit Switches - optical / mechanical / proximity
- Bob CampBell's control box components and full box solution
- MechMate DIY Control box full spec screened spindle 3phase
- Basic schematic of a typical CNC control box
- Mach3 Pendants
- The SuperTech GeckoPwr IV Electronic Micro Step Motor Controller
- Evaluation of the AGek
- E-Stops - Emergency Stops and then what?
- PMDX parallel port break out card for the MechMate
- Control box cases/enclosures (only the outer, empty box part)
- Limit / Home switches - Mechanical or Proxy?
- ncPod from OEM-Tech
- Setting Up Home Switches
- Questions on Fabrica's control box
- The Simulator - an essential "kitchen table" project
- Solid State Relay (SSR) for switching Router under control of Mach3
- Selflatching relay/contactor
- USB joystick and control panel
- Techlf CPU4BU (France) - USB interface
- Packaged Component Kits
- Setting up a remote pushbutton as an input to Mach3
- Electronic sketches for beginners....
- What's the difference between Home and Limit switches?
- Mains power wiring
- CandCNC.com control box components and full box solution
- Cooling fans
- Using a metal enclosure for the electrics vs "plastic" enclosures
- usb to db25 parallel cable
- 5-axis control, G100 (GeckoRex), and Rabbits - it's a zoo!
- Anyone have a MechMate controller fully documented?
- Have SB PRT Alpha ('04 model) - want to drive with Mach3 and parallel cable
- The hardware interface between PC and motor drives - the future beyond parallel BOB?
- Smoothstepper USB to parallel converter
- Need help with some part #
- Changing Shopbot board to G -code
- Programmable Relay to Watch Dog the Limit/Home sequence
- Running 5 drives off one PMDX-122 board
- Slaving a motor - put its drive in parallel to another drive on the same BOB output
- Using limit/home switches to autosquare the gantry
- Z-zero plate - for calibrating z-height to workpiece or table
- Ipac - many extra Mach inputs via the keyboard port
- Logitrol System Complete package info
- question on the estop wiring
- cnc4pc board help
- Version 201 Controller Board from ShopBot
- Ladder Logic
- Would Parker Compumotor OEM650 drives work with the Oriental Motors?
- Printer Cable Box - Connector
- Home Supply Requirements
- PMDX and Gecko 203
- why two proxies on gantry?
- PMDX-122 relay output voltage?
- General wiring, supply voltages, relays, E-stop considerations
- Basics of connecting E-stop Contactor & (Door) Isolator switch
- PMDX-132 instead of the PMDX-122
- AC motor & VFD used with Mach3 in large CNC stone cutting system
- Way over my head...
- My PC does not have a parallel port - how can I drive the PMDX-122?
- Gantry & Car Control Boxes, switch info ?
- Servo motor encoder wiring - is my diagram correct?
- Making a wish list
- Setting up E-Stop and Limit Switches in Mach3
- Electronics Order Spreadsheet
- What is a "charge" pump?
- Can I run geckos from the output of the SB board?
- Isolator switch ?
- Router on and off - mach3
- Control Board Help Please
- Control box location ! - Wall vs Table base
- Driving a relay using 2n3904
- Help choosing a controller for a Pilot Pro router
- Router Speed/RPM Control
- How many CAR STOPPER BLOCKS do I need?
- i need of help
- PMDX-122 vs PMDX-125?
- Contactor for 115V...
- Cheap Control Box
- limit-settings/pin's and port's
- c11 board video input mach3
- Making full use of the PMDX-122
- mach 3 setup help
- Advice on Proximity Sensors
- Vibration and Feedback Problems - C10 BOB with KL4030 Drivers and KL23H286208B Motors
- Relay info
- Trouble with contactor
- Going from 30amps to 15amps
- Control logic if one drive fails?
- Stepper motor connectors
- Green and yellow switches
- need help
- Need opinion on breakout board
- All electronic components, what i have to buy?
- Terminal Blocks - Styles and DIN Rails?
- Alternatives to Gecko Drive?
- What voltage power suply?
- PC inside the Control box...GOOD or BAD idea?
- Contactor and Mach Estop...
- Complex proxy suggestion
- TIP142 Stepper motor driver
- inverter wiring help
- Affordable Pendants DIY article
- auto zero with limited inputs
- Home switches?
- opinion on breakout board
- How to Wire in Series
- Z Home/Limit with ATO Plate....
- What switches to have on control box?
- Stepper Motors
- Zero plate wiring and tool height?
- Hello Can someone help me
- VFD Control Switch Question
- Stepper motor speed problem.
- Anyone can help for moter turning setup
- PMDX 126 BOB Setup
- Using an Arduino to solve common interface problems
- Building an Enclosure
- Push Button Problem