|
|
#1
Thu 09 September 2010, 12:22
|
|||
|
|||
|
Model Bridge for the President of the country
Well this was my first job!
Its not typical Mechmate task but I was only one to accept to make the model of this dual bridge in two days! Ofcourse MM helped a lot  It was delivered to the President of Republika Srpska as a gift from our country as the bridge is on Sava river between our two countrys. Enjoy the pictures! Its made of pressed pvc "Forex" very nice material and lightweight.         Last edited by Gerald D; Fri 10 September 2010 at 05:54.. 
|
|
#2
Thu 09 September 2010, 12:30
|
|||
|
|||
|
Impressive. Well done
|
|
#3
Thu 09 September 2010, 13:25
|
|||
|
|||
|
Very cool. I like it.
|
|
#4
Thu 09 September 2010, 14:45
|
|||
|
|||
|
my favourite.
|
|
#5
Thu 09 September 2010, 17:18
|
|||
|
|||
|
Very Nice.
Was this your design, or did you get cad files for this?
|
|
#6
Thu 09 September 2010, 17:20
|
|||
|
|||
|
My design. I only got pictures of finished bridge, it had to be suprise so they did not ask for files from architects
|
|
#7
Thu 09 September 2010, 18:53
|
|||
|
|||
|
Very well done.
|
|
#8
Thu 09 September 2010, 18:57
|
|||
|
|||
|
That must have been a very loooong night!!!
Looks great!
|
|
#9
Thu 09 September 2010, 22:02
|
|||
|
|||
|
beautiful
very impressive work
|
|
#10
Thu 09 September 2010, 22:46
|
|||
|
|||
|
Brilliant!
|
|
#11
Thu 09 September 2010, 23:01
|
|||
|
|||
|
How did you keep all those small pieces on the table while cutting ?
|
|
#12
Thu 09 September 2010, 23:38
|
|||
|
|||
|
Quote:
|
|
#13
Fri 10 September 2010, 00:43
|
|||
|
|||
|
Danilo,
Very cool. Congratulations on an excellent job. Please share with us some of the details of how you did the job. Thanks
|
|
#14
Fri 10 September 2010, 02:12
|
|||
|
|||
|
way too cool
|
|
#15
Fri 10 September 2010, 02:20
|
|||
|
|||
|
Its 3mm forex sheet I used double sided tape, but it was too thin and it required me to hold it down with my hand sometime (watch your fingers
) becouse no matter what it would pull it up its just to flexible. I tryed climbmill inside and conventional outside, becouse of material vibration (inside lines are 1-1.5mm and would brake on first test) so it doesnt tear thin lines. Edge was fine but required some work becouse forex has a thin layer on both sides (used for printing) and it swarfs (I think this is the right word)Small pieces were made using 4 bridges 2mm wide and 1mm just enough to hold it down so it would not fly on to router bit after being cut out. Router bit used was 2mm endmill
|
|
#16
Fri 10 September 2010, 05:53
|
|||
|
|||
|
Very Nice!
You are taking away jobs from the laser guys!! Great! Had to google that republic name, I knew Bosnia Herzegovina, but Republika Srpska was new to me. Regarding the job, what I do sometimes with thin sheets is prepare an extra gcode program for drilling 1 mm holes in areas I will not cut and then hammer small nails all over the place, this adds some unevenness to the material (it compresses a little more around the nail) but I solve it by making the cuts a little deeper, the spoil board suffers but the job gets done! Last edited by PEU; Fri 10 September 2010 at 05:59..
|
|
#17
Sat 11 September 2010, 01:57
|
|||
|
|||
|
Very impressive! Good job pal!
|
|
#18
Tue 28 September 2010, 04:21
|
|||
|
|||
|
Would it be too much to ask for dxfs and such?
This would make a nice gift for a nephew of mine
|
|
#19
Tue 28 September 2010, 06:18
|
|||
|
|||
|
Send me your email to PM.
will be glad to share
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Make your own V-Rollers if too expensive in your country | Gerald_D | Rails & Rollers | 58 | Wed 11 December 2024 22:48 |
| Router Make and Model | domino11 | 50. Toolheads | 20 | Sat 04 April 2009 11:26 |
| Master CNC - 3D model creation and production | Master CNC | The Market Place | 8 | Fri 27 March 2009 07:02 |
| Have SB PRT Alpha ('04 model) - want to drive with Mach3 and parallel cable | Gerald D | 70. Control Systems | 3 | Thu 08 November 2007 16:10 |
