MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Common Assemblies & Parts > Profiled (laser cut) & bent steel plate
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #61  
Old Thu 05 February 2009, 21:34
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Laser Cut Parts

I should be getting 10 more sets back from the fabricators next week.
Parts and Logos are $474.00

Shipping charges on the average are $65.00 in the lower 48 States for a 65lb box.
I wish that I could help outside the US, but shipping is as much or more than the parts.

For those people sitting on the fence wanting to buy or if you contacted me and haven't pulled the trigger yet. Shoot me a email at: 1mclain@bellsouth.net

This should be about 80 sets sold so far.
That's a lot of dead lifts.

Thanks
Joe
Reply With Quote
  #62  
Old Fri 06 February 2009, 05:58
MetalHead
Just call me: Mike
 
Columbiana AL
United States of America
Now I get it!! Since you are a fitness guru extrodinare.. ... This is how you get to justify being in the "Shop"... "Honey I'm workin out, be up after while." I still owe you a visit...
Reply With Quote
  #63  
Old Fri 06 February 2009, 06:53
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
My wife is pretty cool with me woodworking. I tell her it keeps me out of the bar, and its much cheaper too. Boy do I think, I have her fooled.
Mike I should be in the shop tomorrow if you want to swing by. Give me a shout first before you head my way.

Joe
Reply With Quote
  #64  
Old Sat 21 February 2009, 13:51
woodlab
Just call me: Jake
 
St. Paul, MN
United States of America
What Parts?

Sorry for the newbie question, but what pre-fabbed parts are included in these packages? I'm looking to build a MM, but I prefer to not get into the fabrication of parts. Assembly I can do...but fab...no thanks.
Reply With Quote
  #65  
Old Sun 22 February 2009, 04:31
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Just to let you know, the kit that I am selling is all the laser cut parts under the “Full Options” Colum. I have also included 5 MechMate Logos, 8 sealed bearing for the rail skate, and DIY Leg Leveler parts.
You will still need to order your steel for the table and gantry. If you don’t have access to a mill, you might commission someone in the forum to mill out a few extras.
I am having a few internet issues that won’t let me send large files at the moment. If you would like I can send you some pictures of what is in the kit and/or post it on the forum by
Wednesday.

Joe
Reply With Quote
  #66  
Old Sun 22 February 2009, 05:26
sailfl
Just call me: Nils #12
 
Winter Park, FL
United States of America
Jake

If you have been looking at the forum and users build, you will see the parts that Joe is talking about. There have been lots of pictures of them. Joe has very good tolerance in his parts and the price and delivery are excellent.

Joe, that ought to get some points for any thing I need in the future!!
Reply With Quote
  #67  
Old Sun 22 February 2009, 07:37
J.R. Hatcher
Just call me: J.R. #4
 
Wilmington, North Carolina
United States of America
Send a message via Skype™ to J.R. Hatcher
Joe I didn't know you were trading parts for advertising...............

BUY YOUR PARTS FROM JOE.....BUY YOUR PARTS FROM JOE.....BUY YOUR PARTS FROM JOE.....BUY YOUR PARTS FROM JOE.....

There, that should be good enough for 1 complete set. Ship them to Wilmington, NC

oops forgot about shipping ........................BUY YOUR PARTS FROM JOE.....
Reply With Quote
  #68  
Old Sun 22 February 2009, 07:46
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
Quote:
Originally Posted by woodlab View Post
Sorry for the newbie question, but what pre-fabbed parts are included in these packages? I'm looking to build a MM, but I prefer to not get into the fabrication of parts. Assembly I can do...but fab...no thanks.
Nobody is sending out parts that are sawn, or welded, or drilled, or thread tapped, or cleaned, or painted. If that sounds like too much work for you, then a MechMate is not your solution.
Reply With Quote
  #69  
Old Sun 22 February 2009, 08:11
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
J.R. You are cracking me up. You must be a Doctor too because, I am feeling a little under the weather and all of a sudden I'm starting to feel better.

Sean is waiting to see what I do with my spindle. To tell you the truth, So am I.

But if you need a set I always keep a few on hand.
I'm just glad to be a service to you guys.

Joe
Reply With Quote
  #70  
Old Sun 22 February 2009, 08:19
J.R. Hatcher
Just call me: J.R. #4
 
Wilmington, North Carolina
United States of America
Send a message via Skype™ to J.R. Hatcher
Just throw the extra cash ($275.00 for the office visit) right in the box with the free parts. Sorry about not being setup to take your insurance card.
Reply With Quote
  #71  
Old Sun 22 February 2009, 17:17
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
I will have to pay you when I get my stemuless check.
I would sell a kidney, but you would charge me more money to take it out.
Lord I can see it now.... The Mechmate with a scaple atatched to it.
Reply With Quote
  #72  
Old Sun 01 March 2009, 16:29
venomxx
Just call me: .
 
columbia(MO)
United States of America
Picture of the complete set ?

hi,
Do you have pictures of a complete CNC with this set ?
Reply With Quote
  #73  
Old Sun 01 March 2009, 18:51
domino11
Just call me: Heath
 
Cornwall, Ontario
Canada
Just have a look at any of the build logs in Machines already cutting, they all use the same parts.
Reply With Quote
  #74  
Old Sun 01 March 2009, 20:44
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Sorry, I have been out of town for a few days.
Heath is right, they are all the same parts everyone has been using for the past year.
When you start your build, you will be very pleased how the Y-Car just snaps together. Thanks to the hard work of our Master designer, Gerald.

thanks
joe
Reply With Quote
  #75  
Old Mon 02 March 2009, 17:39
MetalHead
Just call me: Mike
 
Columbiana AL
United States of America
I swear I am coming over!!!! I have been going crazy on some plaques I did for a Wrestling tournement.
Reply With Quote
  #76  
Old Sun 08 March 2009, 09:41
MachineMonkey
Just call me: Kalo
 
Marysville
United States of America
Hi Joe. Great work you're doing with this. Hope to be able to contribute in some small way myself eventually.
Can I get a price with shipping to 95818-2098 ?
This is a business address.
Thanks,
Kalo
Reply With Quote
  #77  
Old Sun 08 March 2009, 20:12
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Kalo, I sent you a PM.

Joe
Reply With Quote
  #78  
Old Mon 16 March 2009, 07:54
docarter
Just call me: Donna #87
 
Suwanee, Georgia
United States of America
Need Parts

Hi Joe,

I've decide to make me a machine. Could you please give me a quote for the following 30024-7632. This is a residence. I'm looking forward to working on this
Reply With Quote
  #79  
Old Mon 16 March 2009, 09:21
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Laser Cut Parts

You are in luck, I have a few sets on hand.

Ill send you a PM when I find out the shipping.

Thanks
Joe
Reply With Quote
  #80  
Old Tue 17 March 2009, 13:13
docarter
Just call me: Donna #87
 
Suwanee, Georgia
United States of America
Hi Joe,

Just received my package, that's some service you got The parts look great! I still have several more items to go before I open up my own build.
Thanks in advance for your support.
Reply With Quote
  #81  
Old Tue 21 April 2009, 14:21
aleiprecht
Just call me: Albi
 
St. Johns
Antigua and Barbuda
Hi Joe ...

you've got mail
Reply With Quote
  #82  
Old Wed 29 April 2009, 13:33
smreish
Just call me: Sean - #5, 28, 58 and others
 
Orlando, Florida
United States of America
Joe - got parts left? I'm ready for another machine.
Reply With Quote
  #83  
Old Wed 29 April 2009, 20:18
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Parts

You are in luck, I have a few sets available.
Resend me your zip so I can figure out shipping.

Joe
Reply With Quote
  #84  
Old Mon 18 May 2009, 03:36
cvriv.charles
Just call me: charles
 
New Jersey
United States of America
Wow, I thought all the lasered parts cut and bent would cost way more than that! LOL. God I cant wait to get a place to build one of these. When the time comes I will buy a set from you. I got your email saved.
Reply With Quote
  #85  
Old Mon 18 May 2009, 05:57
smreish
Just call me: Sean - #5, 28, 58 and others
 
Orlando, Florida
United States of America
Got mine in last week! Thanks Joe. Perfect as always.
Reply With Quote
  #86  
Old Mon 18 May 2009, 11:42
jbmclain
Just call me: Joe #42
 
Birmingham, AL
United States of America
Laser Cut Parts

I still have a few sets left.
Let me know when you get ready to start your build.

Joe
Reply With Quote
  #87  
Old Mon 18 May 2009, 22:47
cvriv.charles
Just call me: charles
 
New Jersey
United States of America
Hey thanks for the reply. If I need a few extra's pieces I could just tell you what they are and you'll take care of all that for me? I only ask because it appears you are selling the parts in kits per machine.

I'm pretty sure once I build this mechmate I will probably go ahead and build another soon after.

Last edited by cvriv.charles; Mon 18 May 2009 at 23:17..
Reply With Quote
  #88  
Old Mon 18 May 2009, 22:56
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
Charles, another difference with this forum is that we frown on quoting the full prior post when making a reply post. Please see: Using quotes when replying to a post - only use if essential please
Reply With Quote
  #89  
Old Mon 18 May 2009, 23:21
cvriv.charles
Just call me: charles
 
New Jersey
United States of America
Sorry GD. Wont do it again. If you catch me doing it again you can let me have it.

Now a quick question,... these parts would be made using metric or imperial? I am thinking imperial because their made within the usa. But what do I know.

Thanks.
Reply With Quote
  #90  
Old Mon 18 May 2009, 23:28
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
The thicknesses will be closest imperial, but the 2D profile will be as per the DXF.
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Laser Cut and Bent Parts - Europe milkov Profiled (laser cut) & bent steel plate 33 Fri 17 August 2012 13:13
Laser Cut and Bent Parts - India dsingh82 The Market Place 10 Thu 01 October 2009 04:14
Laser cut and formed parts Castone Profiled (laser cut) & bent steel plate 5 Sat 05 September 2009 00:40
Greetings all From United States derekkest Introduce yourself and start planning 3 Tue 09 June 2009 06:29
laser burnt pre-bent parts ghostlx Archives 4 Mon 22 September 2008 05:18


All times are GMT -6. The time now is 20:51.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.