#1
|
|||
|
|||
Feeds and Speeds #84 - Mortara, Italy
Thank you all for the help, especially Gerald for drawings.
I am Croatian from Opatija but I liv in Mortara - Italy (20 years). I have started last Christmas with MechMate and the reason why I have not write in this forum is my bad knowledge of English. I mus use the vocabulary when I reed the messages. Fortunately there are many photos in. I am architectoni modeler and this is the reason why I want to built this machine. Not for cutting but for modeling. I am good in working wood and this is the first time I working iron. ( My welding makes cry) I am very sorry because my experience will not be much useful. Technical data: Mech Mate 150 x 200 cm X and Y rails - V-guides on iron profile ( Pacific Bearings, v-guides + wheels + bushings cost me app. 600 €) Racks from Chiaravalle Some photos: mach1.gifx-rail.gif x-rail integro.gify-car.gif v-guide.gif I have found this problems: On the spider plat the wheel holes are distant 132mm app. and that was to short for me. look photos: rupenepoklapaju.gifcalibro.gif calibrorupe.gif Fabricas suggestion: Weld the screw in the holes, filing, drilling new holes and taping. vitisaldate.gifvitilimate.gif dist140.gifnuovibuchi.gif nuovifiletti.gif To put surface in plane smeriglia.gifdoposmeriglia.gif Glass control and paralel control vetro.gifcontroloparalelo.gif Everything is smooth and perfect gaugeplatein.gif (I like the sound when the wheels rolling on guides) Then I find that last 6 holes on the gauge plate not correspond with holes on the z-slide tube. I think the quotes are wrong??? Now I have to do with motors and electricity. HSD offers me a good price (480€) for MT 1073 Y6162Y0010 , 1.5 kW 220 V 18000 rpm. Am I wrong??? In my laboratory is instsled only 3.5 kW. Its just 1 month I study the electrical components (in free time), and I want be sure in configuration which is good for me. I don't need speed but good finish. I have think about 24 gear pinion, Oriental motors 1:7.2, gecko drives 203, PDM 122. I don't know how t instal E-stops and how to conect them, imagine for the other components. It will be a good school. I am very proud for the things I have just done. Thank you all and best wishes. Panorama from my home in Croatia opatija.gif |
#2
|
|||
|
|||
Vanja,
Welcome to the forum. Your build looks great! Nice job. Please continue to share your progress with us. Your experience may help someone else. You never know. |
#3
|
|||
|
|||
Welcome Vanja! Your English is quite okay - I understand you. Sorry about the drawing problems, I will check them. Your progress is great!.
Is your house in Opatija available for holiday rent? |
#4
|
|||
|
|||
Yes it is. I can send you soe photos of the place if you want!?!
|
#5
|
|||
|
|||
What a view,wow
|
#6
|
|||
|
|||
Welcome aboard and yes, you may just bring more useful experience than you think, all work is good to see & compare too.
Plus if you participate in this forum, your future usage & experience with your MM will be useful and good source to this fun community. Congratulation on your progress and please come back some more photos as you progress ! Best of luck |
#7
|
|||
|
|||
control box and mach3
This is what I have done last weeks after one year pause.
Attachment 11318 power sopply 2x 25 V parallel wiring, two condensers 22000uF and 10000uF. I have try to take 9 V from toroid makeing 22 loops around. First time I have misurated the voltage it was 9 V. When I fixed it on the iron plate I have misurated again and the voltage was 6 V. Than I decided that it is better not to risk and I buy a 5 - 9 - 12 V transformator. I have orderd a new computer for move the motors and I ask the vendor to put on one parallel port. He puts me on PCI parallel board Kraun KR.g5 sunix 1888 with two parallel ports. It was monday. How to find the port adress? First problem was that my PCI bord was not enabled PnP in BIOS.(Bios-advanced-PCI PnP- plug and play o/s [YES]). Than I find te adress here: device-management copia.gif It was wednesday. Second problem was that short conection E-stop was very bad and at the moments make false alarm on mach3. I have changed the wire(number 3 above). Than I forgeted to enable charge pump on pin 17 in MACH3.(I've think I dont need it because "I have not any pump on my machine".) I have spend days on google search to find the solution but the solution was in MechMate forum. The led (number 2 above) on pmdx122 is E-stop. If it lit motors dont turn. The led (number 1 above) is the heart of pmdx122. If it don't lit nothing moves. pd122 copia.gif Friday finaly I turn first motor.What a lovely sound it has. wiring.jpg Thanks to all !!!!!! |
#8
|
|||
|
|||
Welcome back Vanja!
|
#9
|
|||
|
|||
Nice to see more Croatians here!
@Vanja Pogledaj nas pocetak rada na MM plazmi pod rubrikom pocetak gradnje! |
#10
|
|||
|
|||
vec vidjeno.Puno citam, malo pisem (slab engleski)
I hope you help me to translate some things when I find difficulties |
#11
|
|||
|
|||
Nema problema, samo javi kada te nesto muci!
|
#12
|
|||
|
|||
Nice to hear from you Vanja!
|
#13
|
|||
|
|||
Thanks for your contribution
|
#14
|
|||
|
|||
two tipe of pinons - 24 and 35 teeth
2pinons.gif I wontn to put 35 teeth pinon but I can because is to big. My rail is to high. vguidehight.gif Can I alarge the hole on the picture above??? I need only 3mm!!! hole.gifgen.gif Or maybe is better to change the design of motor plate?!? |
#15
|
|||
|
|||
I see no reason why you can't extend that slot; it's a guide and it isn't load bearing. In fact, although it wouldn't be as pretty, you could likely extend it right to the edge of the plate.
Two other possibilities: Cut off the tab for the other (hinge) bolt, and weld it back on a little longer, or even simpler - drill a new hole in the gantry below the existing hinge bolt hole. |
#16
|
|||
|
|||
The last solution is the simpliest and probably the best,
Thanks |
#17
|
|||
|
|||
On MM #5 I had to relocate the pivot hole on the gantry to allow for larger pinions on a special project. Easy to do - just remember to countersink that hole!
Sean |
#18
|
|||
|
|||
I had the same problem on MechMate #6. I measured 28mm hight from the inside of the angle iron. The slotting of the motor mount plate took care of the problem.
|
#19
|
|||
|
|||
Yes, cause there is not space to do the other hole in the gantry. Than is difficult to countersink the hole now.
Other problem i have seen is to hold sloted screw head when you mount the motor. Maybe this can be solution for pinons up to 36 teeths newmotorplate copia.gif |
#20
|
|||
|
|||
Seems it work!
Seems it work !!!!!!!!!!!!!!!
http://www.youtube.com/watch?v=3oeeFKJqf2w Last edited by Gerald D; Tue 14 June 2011 at 20:53.. Reason: fixed link |
#21
|
|||
|
|||
Vanja, Youtube is still loading your file . . . . .
|
#22
|
|||
|
|||
don't know if it matters but with the end letter "w" small it works
http://www.youtube.com/watch?v=3oeeFKJqf2w |
#23
|
|||
|
|||
Yes, it works and looks great - well done!
|
#24
|
|||
|
|||
Fortunatly there are meny other things to do (spindle,limit swiches etc).
Mech Mate is never finished.... (Hvala Danilo) I have a litle problem with Mach blue probing.Zero plate works but center finding seems to work with inches insted of mm. Maybee someone have idea how I can change the program? I have not find solution in mach forum and cnc forum. |
#25
|
|||
|
|||
Congratulations Vanja, enjoy playing with the new toy.
|
#26
|
|||
|
|||
Be sure to download latest version
http://www.machsupport.com/screens/M...by_Big-Tex.zip It should have the metric/inch check with GetOemLED(801) in tool zeroing, but I also don't see it it the PROBES section for center finding. Here is the screenset which one user on cnczone changed to metric, try this one but be sure to have a finger on a RESET button if anything goes wrong. just copy this file to Mach directory and load it View->Load Screens. cnc.rs/mechmate/MachBlue_probing_metric_version2.set this is the thread on cnczone where I found it http://www.cnczone.com/forums/mach_w...big-tex-7.html Also if you want to check the button script, go to Mach3 menu... Operator->Edit Button Script and click on a button you need. Pozdrav! |
#27
|
|||
|
|||
I think that this should solve it faster:
go to Operator -> Edit button Script , click on a button for center finding, look for a line that says " XNew = Xcurrent - 3 'probe 3 inches to left " just change the number 3 with amount of millimeters you need, you have 3 more occurrences of this command, for x+ , y- and y+ also edit other buttons to you liking ! |
#28
|
|||
|
|||
I will try tomorow!
|
#29
|
|||
|
|||
Nice to see another MechMate in action !! You get number 84.
|
#30
|
|||
|
|||
Congratz! Now the real work begins
Cheers Tim |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Starting out to actually cut something - cutters, speeds, depths, directions, etc. | Richards | General - MM Operating | 22 | Tue 09 July 2013 03:02 |
Speeds, Feeds, Materials and Bits | smreish | Cutting various materials - bit selection, feeds, speeds | 65 | Sun 11 March 2012 08:01 |
hello from Italy (Naples) | federicodimeo | Introduce yourself and start planning | 1 | Mon 25 October 2010 11:24 |
Hello to all from Italy | Biribago | Introduce yourself and start planning | 2 | Tue 06 April 2010 21:58 |
Ciao from Italy ! | silverdog | Introduce yourself and start planning | 15 | Thu 04 June 2009 12:37 |