#1
|
|||
|
|||
Power supply for the PMDX-122 Parallel breakout board - 9V AC from main transformer
The 9v ac is for the pmdx-122. I'd like to get a coil with that tap included if possible.
Thanks, Greg |
#2
|
|||
|
|||
We have just wound a couple of coils of insulated wire onto(through?) the main toroidal transformer to get the 9V. It is so simple that I am kicking myself for having bought a special small 9V transformer in the first place.
|
#3
|
|||
|
|||
My plan was to power the PMDX-122 with the USB port. Take a surplus USB cable, isolate the power wires and polarity, and tie them into the 5 volt output on the antek power supply. Then plug the USB into the PMDX-122. I have powered other devices this way in the past. Watch my thread, and see if it works. I should be performing a simulation in the next couple of days.
|
#4
|
|||
|
|||
Hey ya'll.
When I ordered my transformer the 600W, 56V I also ordered the 12V and 5V taps with it. No real cost difference. I paid 150$ with shipping. The hope was that I could have the ability to change out to the NCpod after a while if necessary and have the right voltages available. Also, the 12V helps due to the PLC or Programmable relays require 12 to 28 Volts for operation. Just my 2 cents. |
#5
|
|||
|
|||
Can you use a 12v tap with the 9v PMDX-122?
Gerald's idea sounds great if it's just a few wraps of wire to get the 9v. The idea of powering up with a USB port is also interesting if that can work out. Thanks, Greg |
#6
|
|||
|
|||
What I don't like about the powering to the USB port, with a cable from the PC, is the fact that there has to be another cable from the PC to the control box. Also, I am nervous that this could introduce some "ground loops".
|
#7
|
|||
|
|||
I am connecting the usb cable to the 5v lead from the Antek power supply. Only thing for me right now is... I think I know the polarity coming off of the Antek, but I'm not 100% certain, and the PMDX-122 seems like the type of device that would give off magic smoke if connected with the wrong polarity.
I also agree, just wrapping some wire around the transformer until it reads 9 volts is ingenious. |
#8
|
|||
|
|||
"I also agree, just wrapping some wire around the transformer until it reads 9 volts is ingenious."
CAUTION Until this is fed through a bridge rectifier it is AC current. |
#9
|
|||
|
|||
|
#10
|
|||
|
|||
Gosh, if the 9v input takes AC, less risk of releasing the magic smoke if I connect it that way...
|
#12
|
|||
|
|||
I wrapped 18 turns of #24 around my torroidal and got 7.6v AC from it. Great idea Gerald!
|
#13
|
|||
|
|||
So you are getting 0.422 volts per turn. 21 turns will give you 9Volt
Other transformers will be different. It is a simple case of wrapping some turns, measuring the voltage per turn, and then calculating how many more/less turns to make. |
#14
|
|||
|
|||
Magnet wire is the right stuff to wrap around the transformer.
An economical buy from Radioshack: three small spools (Use the 22 gauge for 1 amp) Can also be purchased from McMaster-Carr but you will have plenty left over due to their spool sizes. |
#15
|
|||
|
|||
If anyone needs some magnet wire in North America, just let me know and I can send you a sample to do your winding.
|
|
|