MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Electrical & Electronic > 60. Wiring & Cable Management
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Mon 17 November 2014, 05:37
Duds
Just call me: Dale
 
Canberra
Australia
Photos of cabling management requested

Has anyone got some photos of how you managed the cabling from the cable chain to the end of the Y gantry? The drawings show the box duct but did any of you use saddles or rack or tube? Pleas post photos of your cable management at this spot.

Also, how did you run your umbilical? Did you bundle it in some corrugated flex or core drill through the floor and onto rack then back up to your board. Did you drop it from the ceiling on tied to a pole. If you ran on the floor did you use mechanical protection for you umbilical cables, pipe, ramps, false floor? post photos of how you avoid trip hazards and your umbilical.

Thanks

Dale

Last edited by Duds; Mon 17 November 2014 at 05:38.. Reason: fixed error
Reply With Quote
  #2  
Old Mon 17 November 2014, 10:20
smreish
Just call me: Sean - #5, 28, 58 and others
 
Orlando, Florida
United States of America
Dale,
I have used two solutions.
The first, I came out of the x cable chain and turned down to the floor.
Once on the floor, I built a plywood cable ramp about 12" wide to keep signal and power separated until it got to the wall with the control box mounted above.

Second machine, just bundled all the cable into a nice festoon and swag to the wall which was about 24" away on the "non person" side of the machine.

I'll look for pictures later on the home PC.

Sean
Reply With Quote
  #3  
Old Mon 17 November 2014, 13:48
Duds
Just call me: Dale
 
Canberra
Australia
Thanks Sean
Reply With Quote
  #4  
Old Wed 19 November 2014, 22:19
pblackburn
Just call me: Pete #98
 
South-Central Pennsylvania
United States of America
I used PVC pipe to the end of the machine and my enclosure is located not far from the end of the machine.
Reply With Quote
  #5  
Old Thu 20 November 2014, 05:30
KenC
Just call me: Ken
 
Klang
Malaysia
Dale, along the way, someone did part or combination of all the methods you mentioned and more... Some how, everyone has their own concoction on wiring...
Reply With Quote
  #6  
Old Thu 20 November 2014, 15:56
DocTanner
Just call me: Don Ross
 
Blue Ridge, Texas
United States of America
I used Non-Metallic Liquid Tight conduit and connectors. Electrical supply houses sell various sizes. It lays on the floor. After several years it remains undamaged.

DonRoss
Reply With Quote
  #7  
Old Fri 21 November 2014, 11:48
normand blais
Just call me: Normand
 
montreal
Canada
Here are some pictures
http://www.mechmate.com/forums/showthread.php?t=890
Reply With Quote
  #8  
Old Fri 21 November 2014, 14:58
Duds
Just call me: Dale
 
Canberra
Australia
Thanks Don, Normand Ken and Pete.
Reply With Quote
  #9  
Old Fri 21 November 2014, 15:34
Robert M
Just call me: Robert
 
Lac-Brome, Qc
Canada
Send a message via Yahoo to Robert M Send a message via Skype™ to Robert M
I used 1" EMT tubes & ends.....economical & easy to find for me !!

See here : http://www.mechmate.com/forums/showt...&postcount=122

And
p2230026_resize.jpg

Reply With Quote
  #10  
Old Mon 07 February 2022, 22:24
AlexTup
Just call me: Oluluron
 
AlexTupCN
Russia
Send a message via ICQ to AlexTup Send a message via AIM to AlexTup Send a message via Yahoo to AlexTup Send a message via Skype™ to AlexTup
-

Does anyone know of a good way to get my mac pro 30 away in another room?

The firewire and USB I can figure out, but has anyone found a good dual monitor dvi cable? Or wireless?

Thanks,
Shaun
Reply With Quote
  #11  
Old Wed 09 February 2022, 11:11
MetalHead
Just call me: Mike
 
Columbiana AL
United States of America
Check at www.monoprice.com. They have lots of cables.
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Photos Needed MetalHead Miscellaneous / General / Whatever / Catchall 13 Thu 19 January 2012 11:47
Cabling Management with Cable Trays LyndonDevazier The Market Place 0 Tue 17 January 2012 22:22
Attaching photos to posts on this forum Gerald D About this Forum 27 Sun 14 February 2010 13:41
Dust Management System dmoore Archives 8 Fri 20 June 2008 20:53


All times are GMT -6. The time now is 01:22.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.