#61
|
|||
|
|||
Builder's Log Update
Thanks for the updates, Rceja.
Here is the Updated Builder's Log. We are proud of your MechMate too. And such a quick build, only 3 months, less than half the AVERAGE. Good luck as you learn to use your MechMate and keep us posted with pictures (please) of your projects. |
#62
|
|||
|
|||
Felicitaciones!!
Same here |
#63
|
|||
|
|||
Houses look somewhat the same here aswell, you don't have bars if you have a wall of 3 meters though!! That was quite a change when I moved from holland where the biggest wall around a garden is something you can jump over.
|
#64
|
|||
|
|||
Felicidades !! por esa máquina.
Ahora a hacer mucho polvo Saludos. |
#65
|
|||
|
|||
Gracias Ros!!!, finalmente estamos listos para llenar el taller de polvo, ahora deberemos pensar también en la manera de realizar algunos trabajos para recuperar algo de $$$$$, pues nos hemos quedado casi sin plata, jejejej. Sin embargo nos queda un camino largo en la comprensión y aprendizaje del software correspondiente, pero ahí vamos sobre la marcha!!!!!, de igual manera estamos listos para romper cortadores, clamps y lo que sea necesario para aprender, jejejej.
|
#66
|
|||
|
|||
After a while learning about the cam software, finally we did our firs alu cut, we cut or reductor alu plates. It feel fine when you see the MM cutting alu like butter (0.5 mm per pass), 10000 RPM, 6 mm cutter and 20 IPM. Finally we got our plates and the bearings fit just fine, we are very happy of that. We show you some picutres of our plates!!!!
|
#67
|
|||
|
|||
good work! thanks for sharing the specs as i will need them soon for my reduction assembly.
i notice in the pictures you are using a laptop. any issue with mach3? can you share your laptop specs? i'm temporarily running the machine with a laptop but i get buggy responses when using the arrow keys for jogging the axes. |
#68
|
|||
|
|||
Hi Tuan,we use the laptop just for designig with the CAM soft, we have a desktop running Ubuntu and EMC2 to control de MechMate, in fact our laptop does not have a paralell port!!!, i beleive that laptops are not recommended because of latency issues.
In a while i will upload a small video cutting our plates!!. Thanks for your comments!!!! |
#69
|
|||
|
|||
And now,the video of the MM cutting our al reductor plates!!!.
http://www.youtube.com/watch?v=Xyoc0GS33VM |
#70
|
|||
|
|||
So, how did you hold the part down? It sounds like (in the movie) when you translate to the x-cut you get extra bit chatter from the part moving.....or am I missing something?
|
#71
|
|||
|
|||
We use double adhesive tape, several strips along the alu piece, that way you can get a strong holdig force. That's all we did. No chatter at all, in fact it was quite difficult to remove the tape once we finished cutting.
|
#72
|
|||
|
|||
Cool - You have to love machines that help make themselves better
|
#73
|
|||
|
|||
You are right Mike, we love so much our MM, and we are still begening to know it!!!!
|
#74
|
|||
|
|||
Nice work! Well done, thanks for posting. See you on skype...
|
#75
|
|||
|
|||
Que tal yo soy de Tamaulipas y también estoy construyendo una mechmate después publico las fotos y a ver si me puedes ayudar en algunas dudas saludos!!
|
#76
|
|||
|
|||
Con gusto, en todo lo que este de mi parte.
Que bueno que estas en esto,ademas de divertido es una actividad muy interesante. Felicidades y estoy a tus órdenes. |
#77
|
|||
|
|||
Muchas gracias rceja, mira yo empece el proyecto hace tiempo pero lo deje y pues ahora lo estoy retomando ya tengo casi todo lo electrónico y de lo mecánico pues si me faltan algunas cosas, tengo 4 motores de 740 oz pero medijeron que necesitaba utilizar un reductor 3:1, tus motores ya vienen con reductor o tu lo hiciste es que la verdad se me dificulta mucho conseguir las poleas dentadas, la mayoría de las piezas yo las mande pedir a usa pero es mucho rollo para pagar y luego tener que ir por ellas que me recomiendas que haga?, saludos!! Ahh otra duda tus motores de cuanta potencia son es que no se si sean pequeños mis motores o necesito otros
|
#78
|
|||
|
|||
Que tal Alberto. Mira mis motores son pequeños son de menos de 450 Oz, por tanto creo que tus motores son adecuados. Hasta donde entiendo, el reductor se usa principalmentre para que los coretes sean mas finos, si tu trabajo no es de muchisima precision, entonces no creo que requieras de reductores.
Nosotros conseguimos y hemos conseguido poleas en un huesario industrial que hay por aca, me imagino que en tu ciudad debra haber huesarios similares. Pero si te interesas en las poleas yo buscaria la manera de conseguirtelas aca visitando de ves en ves el huesario como lo hago por costumbre.El reductor nosotros lo fabricamos, de hecho el blog puedes observar las placas de aluminio que cortamos. Si te interesa te consigo las poleas y te dibujo las placas para que las mandes a cortar alla, te las mandaria en DXF, deben existir empresas que corten aluminio en tu ciudad. Nosotros las cortamos en nuestra maquina (checate el video que esta mas arriba), nos quedaron bien. como te comento, nuestros motores son pequeños por esa razòn requerimos de los reductores. Saludos. |
#79
|
|||
|
|||
Te lo agradecería mucho si pudieras consegurimelas y yo te deposito el dinero, y pues me surgió otra duda, veo que hay partes que se tienen que mandar cortar en láser, ustedes las mandaron cortar en Guadalajara ?? y como en cuanto sale mandarlas cortar? Y vi que también tienen dobleces eso lo hicieron ustedes? O también lo mandaron hacer, jaja perdón por tantas preguntas pero es que son los primeras personas de mexico que conozco y yo he batallado mucho en conseguir las partes, les mando saludo y gracias!!
|
#80
|
|||
|
|||
#81
|
|||
|
|||
One more picture, this one is our first cut of this kind.
Is 3 mm MDF. cut depth 1.5 mm |
#82
|
|||
|
|||
That made a lot of dust!
|
#83
|
|||
|
|||
Certanily Gerald it did!!!!, We want to thank you again for sharing this wonderful project
|
#84
|
|||
|
|||
after a long time out of the game, finally we are on again in a new location.
I this place it is quite difficult to get a 220 vac line, so we decided to rewire a toroidal transformer to drive the VFD for the spidle. It worked fine !!!!!!! Last edited by rceja; Sat 16 November 2013 at 22:43.. Reason: wrong file size |
#85
|
|||
|
|||
Rhis is a gif picture of the arrange
|
#86
|
|||
|
|||
Welcome back!
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Mexico's 1st Mechmate Finally is cutting #55 - Obregon, Mexico | Conrado_Navarro | MechMates already cutting | 128 | Mon 18 November 2013 12:38 |
It runs! #89 - Monterrey, Mexico | kanankeban | MechMates already cutting | 118 | Tue 17 January 2012 18:42 |
3D Elk cutting (video) #13 - Hagerman, New Mexico | Greg J | MechMates already cutting | 415 | Sat 05 September 2009 20:28 |
Extruded wood? - actually a composite of wood and recycled plastic . . . . . | Gerald D | Miscellaneous / General / Whatever / Catchall | 2 | Wed 02 July 2008 22:51 |
My first cuts | bbreaker | The Show Room | 2 | Sun 22 June 2008 23:06 |