MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Electrical & Electronic > 702. Power Supplies
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Tue 18 May 2010, 12:28
F2DVasek
Just call me: Vasek
 
Perm
Russia
Need Help with Power Supply Selection

Good afternoon!
I apologise that has got into another's theme!
At me a question:

It is required to me запитать 5 motors:
SY85STH156-6204A - 3 pieces (a current of 6,2 amperes)
SY85STH118-6004A - 2 pieces (a current of 6 amperes)
The driver to 80 volt.

Prompt please what transformer to me it is necessary to select for capacity?
As it is correct запитать 5 drivers
If it is possible, draw the scheme.

Yours faithfully Vasily!
Reply With Quote
  #2  
Old Tue 18 May 2010, 17:04
riesvantwisk
Just call me: Ries #46
 
Quito
Ecuador
Send a message via MSN to riesvantwisk Send a message via Skype™ to riesvantwisk
Vasek,

here is the thread that talks about motor selection and calculation : Calculate the Voltage and VA size of the DC power supply for stepper motors/geckos
Reply With Quote
  #3  
Old Wed 19 May 2010, 04:25
Richards
Just call me: Mike
 
South Jordan, UT
United States of America
Because of the motors' inductance, the 80VDC maximum voltage of the stepper driver, you will be limited to 80VDC. A 50VAC transformer will develop 70VDC after rectification. A 55VAC transformer will develop 77VDC after rectification.

The motors will draw a maximum of 30.6A, if they all draw maximum current at the same time. You can probably use a 20A power supply, which is about 66% of 30.6A.

20A X 50VAC = 1,000VA
80,000 X 20A / 50V = 32,000 uF capacitors.

If I were building that power supply, I would use:

1 each 50VAC 1000VA transformer
5 each 6,800uF 160V capacitors (wired parallel)
1 each 400V 50A bridge rectifier

AnTek makes the PS-15N70 that is rated 21-Amps for $210. They also have the PS-10N70 that is rated 14-Amps for $150.
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Why not use an adjustable, regulated power supply? Bob Cole 702. Power Supplies 19 Thu 25 August 2011 10:33
Wiring the PK296A2A-SG7.2 motors & power supply voltage selection Richards Motors & their mountings 97 Fri 29 July 2011 11:46
The Power Supply needs only to supply 2/3 of the rated motor current Gerald D 702. Power Supplies 0 Sat 05 December 2009 21:09
PMDX-122 power supply paul60 702. Power Supplies 1 Thu 10 September 2009 13:51
My power supply voltage is too high - what can I do? revved_up 702. Power Supplies 11 Sun 20 April 2008 20:35


All times are GMT -6. The time now is 10:51.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.