#1
|
|||
|
|||
jbmclain's old start In Fl now.
Hello All,
I am now finishing up and "Is making dust" jbmclain's Old MM build I am not the owner, But am finish it up for Him. Pete out of Tarpon Springs, Fl. The machine is currently in Tampa and doing just fine. Ill post some pics. Pete has in trusted me to finish his machine up So as I said its making dust. Making parts has allowed me to tweak on it. Anyone in the area is welcome to come see it in action. here are some pics too. http://thesn1per.blogspot.com/2013/1...hort-time.html -Sam FWiW: If anyone can offer me any information about this machine in regards to contributing to this forum Im glad to try and fill in the blanks this way this machine and its owner can make it into the record book. Also that others may benefit as well. Last edited by TheSniper; Mon 30 December 2013 at 22:42.. Reason: added content |
#2
|
|||
|
|||
Looks like you've done a very good job. Congrats on the completion! I know that you have a video at the end of the pics but You may try posting a video on youtube to feature it operating so you can acquire a serial number from the mods. I'm sure they'll ask the necessary info for the build log. Again great job, look forward to seeing the particulars.
|
#3
|
|||
|
|||
What do you want to know about the machine? I know some of the history and can talk to Joe if needed.
|
#4
|
|||
|
|||
@ replys,
Im not sure what Information I can supply to contribute. Therefor Im not sure what to even ask. and or what the protocol is for acquiring a serial number. But if I can Im glad to. As one begins to build one of these units. Im sure they learn along the way whats required. And, just fill in the blanks as they go. If Im not mistaken I think this unit was started looong ago. so I dont know what required info was shared if any over this time span. Im sure not only myself but others could perhaps benefit from this info. Ill peruse around the forum and try to get acquainted. Thanks all @TomA: is the youtube vid how one acquires a SN? and if so what a simple youtube video of it running etc? |
#5
|
|||
|
|||
To receive a serial number one should show via picture(s)
- completed machine - logo's adorned in the appropriate locations (side rails, gantry and control box) - list your machine specifics (cutting area size, build started, build ended) in the post. Mike will do the rest! Great job. I watched JB start that machine...years ago. |
#6
|
|||
|
|||
@Smreish:
Great info Ill take some adequate shots showing what you mentioned. Thanks so much. |
#7
|
|||
|
|||
This machine already has a SN. It is #42
|
#8
|
|||
|
|||
@Mh thanks for the info!
Also Im building a dust boot / shoe for it. can can be seen here. http://thesn1per.blogspot.com/2014/0...ic-cambam.html Though Im still waiting for some parts I should be able to cut the last proto- type this week. and then onto the final parts. -Sam |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
where to start | abiyan | 60. Wiring & Cable Management | 3 | Fri 29 March 2013 03:52 |
....my first start..finally | saas | Construction started, but not cutting yet | 1 | Mon 11 March 2013 22:07 |
How to start? | litemover | General - MM Build | 14 | Mon 02 July 2012 02:11 |
New Start -Macclenny, FL | mlscott52 | Introduce yourself and start planning | 4 | Thu 04 August 2011 06:05 |
Where to start, no really! | ChiknNutz | General - MM Build | 6 | Mon 15 December 2008 20:06 |