|
|
#241
Wed 02 December 2009, 04:22
|
|||
|
|||
|
Like what I see here. More pix more pix!
Cheers Ken 
|
|
#242
Wed 02 December 2009, 08:50
|
|||
|
|||
|
folks - I finished Z axis mod's , the reason I took it up was that i observed pitting marks on my 3d carvings, well now they have gone away by 90% , but a bit is left out - I dont exactly know where the problem lies - but sure some day i will sort it out.
|
|
#243
Wed 02 December 2009, 21:12
|
|||
|
|||
|
Irfan, what size linear size are you using? & the stroke length?
|
|
#244
Thu 03 December 2009, 09:20
|
|||
|
|||
|
25mm thk slides 400 mm length, i get a stroke length of just a little less than 5 inches,
you can use 20mm ones too
|
|
#245
Fri 11 December 2009, 22:14
|
|||
|
|||
|
what a MM can do -
Hi Folks - this is what we recently did on our mechmate
http://www.youtube.com/watch?v=DBf5Sco6SmM Last edited by javeria; Fri 11 December 2009 at 22:38..
|
|
#246
Fri 11 December 2009, 22:48
|
|||
|
|||
|
Fantastic!
|
|
#247
Sat 12 December 2009, 01:19
|
|||
|
|||
|
Beautiful Artwork
|
|
#248
Sat 12 December 2009, 03:04
|
|||
|
|||
|
Now this is what I like. Well done Irfan
|
|
#249
Sat 12 December 2009, 06:32
|
|||
|
|||
|
Very good carving ! what kind of wood is it ? can you post picture once you got the finish on . thank
|
|
#250
Sat 12 December 2009, 07:43
|
|||
|
|||
|
That is nice!
|
|
#251
Sat 12 December 2009, 10:15
|
|||
|
|||
|
Thats teak wood slab of 2x3 ft, cost 200USD eq, rough finish took 2hrs, relief took 6 and v bit carving took 4 hrs, started 6 am finished noext morning 1 am.
roughing - 8mm router bit relief - 3mm ball nose v bit - 20 degree 3mm dia v bit
|
|
#252
Sat 12 December 2009, 11:50
|
|||
|
|||
|
Irfan, didn't anybody tell you that you cannot do a job like that with open loop steppers? Were you not supposed to be using servos? How did you fix the marks caused by the lost steps?
|
|
#253
Sat 12 December 2009, 19:50
|
|||
|
|||
|
Irfan, Very well done!
|
|
#254
Sat 12 December 2009, 20:23
|
|||
|
|||
|
Nice
Top notch work!
|
|
#255
Sat 12 December 2009, 21:19
|
|||
|
|||
|
Great work. Irfan. Well done.
|
|
#256
Sat 12 December 2009, 22:18
|
|||
|
|||
|
|
#257
Sun 13 December 2009, 13:05
|
|||
|
|||
|
Irfan, my next tour is to Bangalore
|
|
#258
Sun 13 December 2009, 15:51
|
|||
|
|||
|
awesome! what software did you used?
|
|
#259
Sun 13 December 2009, 21:42
|
|||
|
|||
|
Irfan that looks fantastic.
Did you do the 3D model yourself or someone else? Look forward to pics of it finished. Greg
|
|
#260
Sun 13 December 2009, 22:51
|
|||
|
|||
|
Ah - yes the work is fantastic - but I have just used the relief and changed a couple of tools and waited it out
 The true credit goes to my Artcam guru for the relief and Mechmate (our beloved G') for executing it out. RGDS Irfan
|
|
#261
Mon 14 December 2009, 11:12
|
|||
|
|||
|
Does your Artcam guru sell these type of files. I am sure there are a few of us that would like to buy these types of files. Let me know please.
|
|
#262
Mon 14 December 2009, 11:19
|
|||
|
|||
|
me too....me too...
|
|
#263
Sat 19 December 2009, 08:57
|
|||
|
|||
|
Beautiful carvings. ...
|
|
#264
Sun 20 December 2009, 09:56
|
|||
|
|||
|
need some help
Hi folks - I am on to making a model car for a company for that they have given me a surface model, the problem is that I have use current surfaces which are curved to carve the model out, after finish the model has different heights at the bottom which needs material removal manually, I need help in the region of manual material removal conforming the the end surface of the relief,
hope some one can help me out here RGDS Irfan
|
|
#265
Sun 20 December 2009, 12:23
|
|||
|
|||
|
Irfan,
Very impressive work. If you only need to flat the other side, I would suggest using one of these. I use it for all materials including wood and MDF a lot with very good results. it has very good control over the amount of material removal. My sander is 300mm in diameter. PS106.jpg If you need contoured or pocketed other side, I think you can make a gypsum replica and use it as jig, in order to machine the inside.
|
|
#266
Mon 21 December 2009, 16:22
|
|||
|
|||
|
Irfan,
When you set up the material size, did you reference the Z to the top of the material or the bottom of the material. If it is at the top, use the bottom. See if that doesn't fix the problem.
|
|
#267
Mon 21 December 2009, 19:57
|
|||
|
|||
|
ah never tried that nils, will do that today
|
|
#268
Sat 26 December 2009, 01:54
|
|||
|
|||
|
Nils your advice worked,
and here is the lastest Jali work done on the Mechmate
|
|
#269
Sat 26 December 2009, 03:01
|
|||
|
|||
|
Irfan,
What will those be used for?
|
|
#270
Sat 26 December 2009, 06:06
|
|||
|
|||
|
think above the mosque entrance doors
|
 |
| Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Wood carving - Bangalore, India | issac winfred | Introduce yourself and start planning | 3 | Wed 12 August 2009 09:13 |
| We made it to #3 !! | WTI | Archives | 3 | Thu 05 June 2008 14:57 |
| Laser kits for India - out of Bangalore | javeria | Profiled (laser cut) & bent steel plate | 3 | Tue 13 May 2008 21:50 |
| CNC Router with Servo motors & belt drives (non-MechMate) - Bangalore, India | Irfanulla | Archives | 67 | Mon 01 October 2007 12:11 |
| Hi, new to the gang - Bangalore, India | ANIL | Introduce yourself and start planning | 5 | Sat 09 June 2007 09:45 |
