#1
|
|||
|
|||
New Z-Slide or Prefab Rail Ideas!
Instead of using a plate, that is difficult to grind, why we can use two "classic" rails ?
|
#2
|
|||
|
|||
Actually, the slide plate is super easy to grind.
If you plan on using a ground method as in your second picture, you just buy a 36" length of 100mm x 7mm Cold roll steel plate, then profile like the regular rails. Then, cut to length on each end so you cut off the run off area of the skate profile. Without checking the spider plate, I don't think you have enough clearance between the 45 deg bend in the spider to accommodate that extra width the angle profile adds. I did this grind method 3 times - once for #5 with regular steel and the suggested tool steel on #28 & #58 - it was super fast with 36 grit paper. Plus, doing in your second picture you may run the possibility of "less-than-parallel" slide from point to point based on you assembly method. Just thoughts, Sean Last edited by smreish; Fri 01 February 2013 at 06:53.. |
#3
|
|||
|
|||
I agree that the "current" slide isn't rigid enough. BUT when looking at it as a whole, i.e. compact, weight & difficulties to fabricate. It is the best compromise... so far.
IMHO, The "New" design works too. The "less-than-parallel" can be corrected with some shims using the Fish line + filler gauge. The point to consider is whether do you really wanna go through the hassle? Also, unless you use thinner & smaller angle iron, I don't see any benefit in weight saving. If you are too lazy to hand grind, just get is on a milling machine. Nevertheless, it is still a good attempt to improve on the current design. Last edited by KenC; Fri 01 February 2013 at 19:06.. |
#4
|
|||
|
|||
Has anyone seen the makerslide design? This was interesting to say the least, very similar to the mechmate slide, cheap, and perhaps it could be incorporated into the mechmate somehow. It is a custom extrusion with rails for about $60 for 6'.
BTW, I think the mechmate slide is very cool, and griding the plate is easy. http://www.kickstarter.com/projects/...bearing-system http://makerslide.com Last edited by litemover; Fri 26 April 2013 at 09:17.. |
#5
|
|||
|
|||
Having seen the amount of wear on a mild steel slide, and upgrading to tool steel for the z-axis, an aluminium slide will simply not give enough life.
|
#6
|
|||
|
|||
Those sort of extrusions need steel raceways to be very useful.
Example: http://www.pbclinear.de/pbclinear/pd...rospekt_A4.pdf |
#7
|
|||
|
|||
That's fantastic looking stuff Jason.
I'm sure it does wear much faster than steel but the extrusion from makerslide's targeted price is at $3 per foot. |
#8
|
|||
|
|||
Extrusion is cheaper, but do you really enjoy replace the worn AL extrusion every now & than? I would rather waste my time doing other unproductive activities...
|
#9
|
|||
|
|||
My idea is to have a system that you can build with the L steel grinded with the "skate". Also you can adjust the parallelism simply with very thin washers.
If you want to change the "nature" of the Z-slide probabiy the best solution is a pair of HIWIN rails. |
#10
|
|||
|
|||
My problem with the makerslide extrusion is the protrusion of the running surface past the side of the extrusion. It looks somewhat weak may bend under pressure from the bearings.
|
#11
|
|||
|
|||
Jason, bear in mind that they are talking plastic wheels . . . . . don't think they will bend the extrusion.
|
#12
|
|||
|
|||
This thread is about the Z-slide. But if someone wants to do a useful extrusion for the other long rails, all we need is this:
The hard insert is readily available from a couple of suppliers, including Rick at Superior Bearings. Any old glue would hold the hard part in place. If someone does want to go this route and borrow the idea from here, please give us credit by sizing the profile so that it fits within the MechMate dimensions |
#13
|
|||
|
|||
Our aluminum supplier will do the extrusion but we'd have to commit to 1500-2000 lbs/year. That's a whole lot of rail.
|
#14
|
|||
|
|||
Quote:
The design will certainly save fabrication time but It won't not allow the Mechmate to cut to its full potential. I like that design Gerald, a drop-in and glue. Jason Last edited by Jason Marsha; Wed 01 May 2013 at 05:38.. |
#15
|
|||
|
|||
Looking at Gerald's drawing above, I wonder if that could be cut from appropriate sized aluminum C channel on a table saw. The channel may need to be oversized to get the required thickness in the fillet.
First pass, with web against fence, trim one leg to height. Second pass, trim the other leg. Third pass(es), web up, dado the first leg Fourth pass(es), dado the other leg. Fifth pass, web down, split into two finished Ls. Sixth pass, if needed, trim the larger L if they weren't equal. |
#16
|
|||
|
|||
just an idea? off the shelf components
RAIL IDEA.jpg
...then use the epoxy method? Or maybe just structural adhesive for the entire assembly? |
#17
|
|||
|
|||
I have worked with Iowa Aluminum who will make extrusion dies and do 500 pound runs with no setup charges. Runs down to 350 pounds can be done for a $200 setup charge. Don Wityshyn was my point of contact.
|
#18
|
|||
|
|||
I don't know if this design will work on a mechmate, but cheap and easy to build, the one in picture is using bishop wisecarvers v-roller guides, the one I built is using rollon
v-roller guides, the diff being the rails and rollers on both are hardened steel but the body on rollon is steel also, I double trucked my z-axis as I have and adjustable gantry from 6 inches to 16 for timber carving. Last edited by danhamm; Thu 06 June 2013 at 00:12.. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Shop Security Ideas | Regnar | General - MM Build | 5 | Wed 27 October 2010 16:13 |
Z-Slide - width allowance for V-Cap rails on edges of slide plate | YRD | 40. Z-Slide | 5 | Tue 11 November 2008 11:20 |
Ideas & Experiments with different rail styles | Arthur Ransom | Rails & Rollers | 38 | Fri 21 December 2007 14:25 |
Mamba logo ideas | smreish | Archives | 18 | Mon 03 December 2007 22:00 |
New Ideas and less Banging your Head - South Africa | GARTH LEE | Introduce yourself and start planning | 1 | Wed 21 February 2007 01:26 |