![]() |
#1
|
|||
|
|||
Model Bridge for the President of the country
Well this was my first job!
Its not typical Mechmate task but I was only one to accept to make the model of this dual bridge in two days! Ofcourse MM helped a lot ![]() It was delivered to the President of Republika Srpska as a gift from our country as the bridge is on Sava river between our two countrys. Enjoy the pictures! Its made of pressed pvc "Forex" very nice material and lightweight. ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Last edited by Gerald D; Fri 10 September 2010 at 05:54.. |
#2
|
|||
|
|||
Impressive. Well done
|
#3
|
|||
|
|||
Very cool. I like it.
![]() |
#4
|
|||
|
|||
my favourite.
![]() |
#5
|
|||
|
|||
Very Nice.
![]() |
#6
|
|||
|
|||
My design. I only got pictures of finished bridge, it had to be suprise so they did not ask for files from architects
|
#7
|
|||
|
|||
Very well done.
|
#8
|
|||
|
|||
That must have been a very loooong night!!!
Looks great! |
#9
|
|||
|
|||
beautiful
very impressive work |
#10
|
|||
|
|||
Brilliant!
|
#11
|
|||
|
|||
How did you keep all those small pieces on the table while cutting ?
|
#12
|
|||
|
|||
That make 2 of us curious to learn.
|
#13
|
|||
|
|||
Danilo,
Very cool. Congratulations on an excellent job. Please share with us some of the details of how you did the job. Thanks |
#14
|
|||
|
|||
way too cool
|
#15
|
|||
|
|||
Its 3mm forex sheet I used double sided tape, but it was too thin and it required me to hold it down with my hand sometime (watch your fingers
![]() Small pieces were made using 4 bridges 2mm wide and 1mm just enough to hold it down so it would not fly on to router bit after being cut out. Router bit used was 2mm endmill |
#16
|
|||
|
|||
Very Nice!
You are taking away jobs from the laser guys!! Great! Had to google that republic name, I knew Bosnia Herzegovina, but Republika Srpska was new to me. Regarding the job, what I do sometimes with thin sheets is prepare an extra gcode program for drilling 1 mm holes in areas I will not cut and then hammer small nails all over the place, this adds some unevenness to the material (it compresses a little more around the nail) but I solve it by making the cuts a little deeper, the spoil board suffers but the job gets done! Last edited by PEU; Fri 10 September 2010 at 05:59.. |
#17
|
|||
|
|||
Very impressive! Good job pal!
|
#18
|
|||
|
|||
Would it be too much to ask for dxfs and such?
![]() This would make a nice gift for a nephew of mine ![]() |
#19
|
|||
|
|||
Send me your email to PM.
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Make your own V-Rollers if too expensive in your country | Gerald_D | Rails & Rollers | 56 | Mon 31 July 2023 01:48 |
Router Make and Model | domino11 | 50. Toolheads | 20 | Sat 04 April 2009 11:26 |
Master CNC - 3D model creation and production | Master CNC | The Market Place | 8 | Fri 27 March 2009 07:02 |
Have SB PRT Alpha ('04 model) - want to drive with Mach3 and parallel cable | Gerald D | 70. Control Systems | 3 | Thu 08 November 2007 16:10 |