MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Structure & Mechanics > 55. Dust Management
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Mon 09 February 2009, 13:46
MariusL
Just call me: Marius #22
 
Centurion
South Africa
Routing the flexible dust hose

Gerald,
Any ideas on how to handle the dust extractor tube. With the table being large it poses a bit of a problem. The dust collector is situated next to the machine midways. The tube is 100mm in diameter. I was thinking of a swing arm with a roller track.
Reply With Quote
  #2  
Old Mon 09 February 2009, 20:58
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
A swing arm with a track under it, and one or two runners supporting the hose, seems to be the best option.
Reply With Quote
  #3  
Old Mon 09 February 2009, 23:42
MariusL
Just call me: Marius #22
 
Centurion
South Africa
Gerald,
Should I make the swing arm to reach the furthest corner? If not, what is the practice?
Reply With Quote
  #4  
Old Tue 10 February 2009, 00:36
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
I don't know of standard practice because I havn't seen enough systems. I think the biggest factor is the amount of ceiling height you have above the table. If you have plenty of height, you don't even need a swing arm. . . .


Note that it helps to support the hose above the z-axis so that it can drop down to a flexible loop after the support.

Here is a fixed arm, again going to point high above the z-axis.

There is no harm in building a swinging arm that stops about a meter short from the furthest corner - you can always cut it shorter later.
Reply With Quote
  #5  
Old Tue 10 February 2009, 00:57
MariusL
Just call me: Marius #22
 
Centurion
South Africa
The area that the machine will work for the first 8 months or so has a very low roof. I will have to go for the swing arm system.
Reply With Quote
  #6  
Old Tue 10 February 2009, 01:09
Alan_c
Just call me: Alan (#11)
 
Cape Town (Western Cape)
South Africa
Send a message via Skype™ to Alan_c
This is the idea I am working on. I propose to use lazy susan type bearings at the pivoting points (so that the dust pipe can pass through it) I also have a very low roof over my machine. The counterweight on the top section is to balance the long section over the machine. The whole assembly must be firmly attached to a wall or steel column. The lengths of the two sections are critical and decided by the position of the fixing point relative to the table. The arm must always have a bend in it (when viewed from above) so that the assembly will fold correctly when the gantry moves to the back.

dust pipe idea.jpg
Reply With Quote
  #7  
Old Tue 10 February 2009, 01:32
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
For very low headroom, there are a couple of guys who strap their dust hoses onto the edges of their cable chains.
http://pacosarea.blogspot.com/2007/0...nc-router.html

Maybe some ideas (and smiles) . . . .
http://www.infraredradiant.com/emerg...e_exhaust.html

Alan, your arm has a tiny illustration on this page:
http://www.infraredradiant.com/neder...ductrange.html

Reel/winch system:
http://www.monoxivent.com/products/1/motor_op_hose.php
Reply With Quote
  #8  
Old Tue 10 February 2009, 02:32
MariusL
Just call me: Marius #22
 
Centurion
South Africa
Thanks for the replies gentlemen, it has given me some good ideas. Due to space constraints, I will have to go for the folded arm idea. I will show pictures later.
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 01:25.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.