MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance > The Show Room
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Fri 17 July 2009, 10:36
lunaj76
Just call me: Justin #24
 
Littleton, (Colorado)
United States of America
Send a message via Skype™ to lunaj76
Flower Carvings and Skateboards! - Littleton, CO

I did these with a free cam software from here.

http://www.vectorart3d.com/machinist_free/
Attached Images
File Type: jpg flower1.jpg (189.9 KB, 2216 views)
File Type: jpg flower 2.jpg (203.1 KB, 2275 views)
Reply With Quote
  #2  
Old Fri 17 July 2009, 11:15
javeria
Just call me: Irfan #33
 
Bangalore
India
what are the bits you used and speed and time it took to complete

good one - did you have to sand it?
Reply With Quote
  #3  
Old Fri 17 July 2009, 11:41
Castone
Just call me: Leo #41
 
Soddy Daisy , Tn
United States of America
Flower

Nice work!
Reply With Quote
  #4  
Old Fri 17 July 2009, 12:39
sailfl
Just call me: Nils #12
 
Winter Park, FL
United States of America
Justin,

That is very nice job.
Reply With Quote
  #5  
Old Fri 17 July 2009, 13:12
Robert M
Just call me: Robert
 
Lac-Brome, Qc
Canada
Send a message via Yahoo to Robert M Send a message via Skype™ to Robert M
Well done & thanks for the tip !
Reply With Quote
  #6  
Old Fri 17 July 2009, 13:12
domino11
Just call me: Heath
 
Cornwall, Ontario
Canada
Very Nice, more info on finishing too!
Reply With Quote
  #7  
Old Fri 17 July 2009, 21:06
lunaj76
Just call me: Justin #24
 
Littleton, (Colorado)
United States of America
Send a message via Skype™ to lunaj76
4 min rough pass w 1/4" ball nose, 26 min finishing pass w 1/8" ball nose. I was not contracted to do the finishing so I did not sand them. I only have these back because they want more and I need to match them up with the new ones. I think I did something like 60ipm on the rough and 50ipm on the finish.
Reply With Quote
  #8  
Old Sat 18 July 2009, 10:39
Khalid
Just call me: khalid
 
Sadiqabad
Pakistan
very beautiful and i like the staining
Reply With Quote
  #9  
Old Mon 13 June 2011, 22:43
lunaj76
Just call me: Justin #24
 
Littleton, (Colorado)
United States of America
Send a message via Skype™ to lunaj76
Long Boards

Cut some prototype skateboards of a local company here.
Attached Images
File Type: jpg SKATE1.jpg (19.4 KB, 1438 views)
File Type: jpg SKATE2.jpg (15.3 KB, 1438 views)
Reply With Quote
  #10  
Old Fri 08 July 2011, 06:30
lunaj76
Just call me: Justin #24
 
Littleton, (Colorado)
United States of America
Send a message via Skype™ to lunaj76
HPL desk for a vets office

I could not have done this job without my Mechmate.
Attached Images
File Type: jpg Tenaker_Desk_2.jpg (140.5 KB, 1282 views)
File Type: jpg Tenaker_Desk_3.jpg (151.7 KB, 1282 views)
File Type: jpg Tenaker_Desk_4.jpg (184.2 KB, 1286 views)
File Type: jpg Tenaker_Desk_5.jpg (154.1 KB, 1282 views)
File Type: jpg Tenaker_Desk_3D.jpg (86.8 KB, 1267 views)
Reply With Quote
  #11  
Old Fri 08 July 2011, 06:33
smreish
Just call me: Sean - #5, 28, 58 and others
 
Orlando, Florida
United States of America
Pretty!
Reply With Quote
  #12  
Old Fri 08 July 2011, 07:17
domino11
Just call me: Heath
 
Cornwall, Ontario
Canada
Nice!
Reply With Quote
  #13  
Old Tue 12 July 2011, 12:43
louloute30
Just call me: Laurent
 
CHAUNY
France
is it MDF ? mélamine ?
Reply With Quote
  #14  
Old Fri 15 July 2011, 21:32
lunaj76
Just call me: Justin #24
 
Littleton, (Colorado)
United States of America
Send a message via Skype™ to lunaj76
It is particle board with Laminate 2 sides. I had the laminate laid up by a local company here.
Reply With Quote
  #15  
Old Sun 17 July 2011, 19:39
David Bryant
Just call me: David #99
 
Western Australia
Australia
Hi Justin
Did you carve a curve into both sides of the skateboards? What was the cutting sequence.
Thanks
David
Reply With Quote
  #16  
Old Wed 20 July 2011, 21:46
lunaj76
Just call me: Justin #24
 
Littleton, (Colorado)
United States of America
Send a message via Skype™ to lunaj76
Hi David,

Are you talking about top and bottom curve? These boards are just flat. I will be doing some boards that will be laminated into a curve. That will be down the road.

Justin
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New Vacuum Table! #67 - Littleton, NC salewis MechMates already cutting 137 Sat 13 October 2012 04:54
Workin for Beer #24 - Littleton, Colorado lunaj76 MechMates already cutting 133 Wed 09 May 2012 08:35
3D Carvings javeria The Show Room 3 Sun 30 May 2010 10:42
Wrestling with Aspire on some carvings - Truckee, CA inventall MechMates already cutting 46 Fri 18 September 2009 16:33


All times are GMT -6. The time now is 11:08.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.