MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance > Troubleshooting
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Mon 30 January 2017, 23:06
rockaukum
Just call me: rockaukum
 
Placerville, ca
United States of America
Help with calibration using Mach3

First off I do not have a MM machine but thought I'd ask here. I am trying to calibrate the motors on a 4x8' table with steppers on R P. I have it spot on for the Y axis. I got it close after four tries on the X axis. The Z axis is another story! I am using Mach3 to do the calibration. I have it set to inches and set the distance to one inch. Do the test and the Z does not move although I can hear the motor humming along then stops making the noise. I return Mach3 to run normally and manually adjust the Z without any issues at all. Any suggestions on what may be going on here? I started the calibration because I did a "test" cut and when the request for the Z to raise came, it would not come all the way up. If any additional information is needed, please ask and I will get it. I am very new to this stuff and don't fully understand so the help is very much appreciated!
Thanks,
Rockaukum
Reply With Quote
  #2  
Old Fri 03 February 2017, 13:25
danilom
Just call me: Danilo #64
 
Novi Sad
Serbia
If you know how many steps it needs for your motor to make one full turn, and if there is any reduction in between you know the ratio, you also know the pitch of the Rack and the number of teeth on the pinion, so there is nothing to be calibrated in mach its just a number which you calculate... Racks if not precision are non linear so it might differ from point to point where you decide to calibrate.

Quote:
it would not come all the way up
what does this mean, how do you know where should it come? do you have a tape measure? zero out the axis DRO ... measure from some point to the axis in question, move it (jog it, mdi move etc...) 100mm, measure again? did it move 100mm?
Reply With Quote
  #3  
Old Fri 03 February 2017, 22:27
rockaukum
Just call me: rockaukum
 
Placerville, ca
United States of America
Thanks Danilom,
I did not build the machine nor have any specs on the machine or its components. I have tried to get this from the person I purchased the machine from. He has informed me that there were no such documentations. I don't really know what drivers are on this and not sure how to find out. I have been messing with this for a little while now and have found that I get one thing straightened out and another pops up. At this time, I think I got it. I figured out how to do the motor tuning which may have been the issue with the Z axis (motor humming and not moving, Stalling??) So I did a bit of motor tuning, then went to the calibration again. X & Y are good but the Z would move to the top and max out against the stop (no limit switches on the machine). Thinking about this, I came to a new trial. If it maxes out the movement with a one inch request, lower the request and see what happens. I went with 1/8" request and the machine moved a lot but stopped before hitting the stop. Now I was getting somewhere. Entered the measured movement and ran the calibration again, After four or five goes at this, I got it. Repeatable results! Life is good again. I am learning this stuff as I go and excited to see some results along the way. If you have any input as to figuring out the drivers (again, don't know where they are) that would be great. As well as finding out if they have any reduction...
Future of the machine... I want to install limit switches, Emergency stop buttons and a controller to adjust the router speed via mach3. Lastly build a vac table. One day, one step at a time... If ya got "how to" links to any of these additions please share.
Now on to figuring out inkscape and sheetcam....
rockaukum
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
CNC ROUTER TWIN BED 8'x10' mach3 jeffg123 The Market Place 0 Tue 20 September 2016 04:49
My USB pendants for Mach3 Andrey67 The Market Place 7 Fri 30 March 2012 10:38
Mach3 Pendants Gerald_D 70. Control Systems 12 Sat 24 July 2010 05:58
Router on and off - mach3 Retief 70. Control Systems 9 Fri 03 July 2009 01:42
X,y and Z zero zero for free on Mach3 Art CNC motion control software 0 Wed 07 May 2008 09:41


All times are GMT -6. The time now is 06:09.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.