#1
|
|||
|
|||
Making Cuts #129 - St Denis, Reunion
Hello.
A report of my project with a modification of the skate. |
#2
|
|||
|
|||
Welcome aboard. It seems to be nice weather out there in this time of year.
|
#3
|
|||
|
|||
The time is beautiful but a cyclone (named BERGUITTA) threatens us at the moment.
|
#4
|
|||
|
|||
Welcome aboard!
|
#5
|
|||
|
|||
Yannick,
I see you've been around about 5 years. Congratulations on your decision to build a MechMate and on your progress so far. Regarding the skate. Do I see bolt ends at the far left and far right of the photo? When I used a similarly designed skate, the bolts that rode the top of the rail "wore" to the point that my depth of cut was affected. Thus the grinding wheel became more aggressive on subsequent passes. After noticing this, I found that I had to keep adjusting the bolts as they wore. To remedy this, later designs of the skate placed bearings where you have bolts so the bearings could ride the top of the rail. The bearings don't wear as you make your passes resulting in better control of the depth of cut. |
#6
|
|||
|
|||
john,
you are right. the bolts affect the top of the rail but as I finished the rails. I did not notice or forget that the skateboard was planned for 115mm and not for the 125mm discs. |
#7
|
|||
|
|||
Hello.
|
#8
|
|||
|
|||
Well good. That's a tough job COMPLETE! I hope you're happy with the results.
Thanks for sharing more progress photos. Last edited by jhiggins7; Sat 20 January 2018 at 05:06.. Reason: Added comment. |
#9
|
|||
|
|||
10.40.364 steel tubing replacement
hello. can i replace this part 10.40.364 (50x25x3 steel tubing) by this 60x30x3 without problems. when i look the plan it seem possible. but i'm not sure about the screws or something else.
|
#10
|
|||
|
|||
Sous le soleil de l'île de la Réunion / Under the sun of the Reunion Island
a link to discover "the ultimate island"
(It is not from me it is the tourist office) https://en.reunion.fr/ |
#11
|
|||
|
|||
Hello
Gantry
Last edited by YANLM; Mon 22 January 2018 at 08:27.. |
#12
|
|||
|
|||
What a exotic place. I discovered it through our forum.
Yannick, you are doing good progress. |
#13
|
|||
|
|||
Progress looking great. Glad to see build posts!!
|
#14
|
|||
|
|||
..."Glad to see build posts"...ici aussi
|
#15
|
|||
|
|||
Hello, photo of the construction. I am going to begin the electric part soon
Last edited by YANLM; Sun 04 February 2018 at 07:44.. |
#16
|
|||
|
|||
it's not easy but with a bit of patience.
Last edited by YANLM; Mon 05 February 2018 at 10:42.. |
#17
|
|||
|
|||
Looking great! Like the progress.
|
#18
|
|||
|
|||
some progress
|
#19
|
|||
|
|||
Looking good!
|
#20
|
|||
|
|||
Soon the cabling
|
#21
|
|||
|
|||
I just stopped by to check on you, Yannick. I am hoping good progress for you.
|
#22
|
|||
|
|||
I moved forward on the construction. All the axes work. But at the moment I have difficulty with mach3.
https://youtu.be/xxWOjvbM7t8 |
#23
|
|||
|
|||
If you post a little bit of problem, I help search on here for a solution. "Lots of really talented people, have posted good information. It is just hard to find."
|
#24
|
|||
|
|||
wiring
the wiring is almost complete.
|
#25
|
|||
|
|||
wiring complete
estop and push button too but I am completely blocked by the spindle which does not start with mach3. Anybody would have a vfd Fuling ? |
#26
|
|||
|
|||
The construction in image
|
#27
|
|||
|
|||
Is this the one you have, Yannick? https://www.youtube.com/watch?v=wgZ1dijgvuU
|
#28
|
|||
|
|||
hello Davey, i have seen this video before. It's not the same model but the parameters seems to be the same when i compare with the user manual of my model (downloaded because the user manual delivered with the vfd is in chinese).
In manual mode it work very well. |
#29
|
|||
|
|||
Did you switched parameters from inverter menu to change command source?
P0.01 from 0 to 1 keyboard to terminal control P 0.03 from 0 to 1 to control ferquency instead keyboard 0-10v source https://www.manualslib.com/manual/82...page=21#manual pages 20-21 |
#30
|
|||
|
|||
hello Ivo
Yes i have changed the command source. i see variation on the vfd screen, when i jog 0-10v with the breakout board software. i found 24v between S1 and DCM and variation when i measure between VI and ACM . I found 24 V between S1 and DCM when i activate the relay but i also found 24v when the relay is not select !! and ACM and DCM are connected to 0V on my bob (all 0V on Bob are connected). |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
More progress, it cuts ! #109 - Hampshire, UK | Andrew_standen | MechMates already cutting | 75 | Thu 23 July 2020 13:23 |
First Cuts And Has Stickers! #126 - Genesee, WI | hflwaterski | MechMates already cutting | 215 | Tue 11 April 2017 12:00 |
First Cuts #108 - Willemstad,Netherlands | parrulho | MechMates already cutting | 154 | Sat 15 November 2014 12:14 |
Making First Cuts #56 - Empangeni S. Africa | Lex | MechMates already cutting | 263 | Tue 30 October 2012 23:14 |
My first cuts | bbreaker | The Show Room | 2 | Sun 22 June 2008 23:06 |