MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Personal Build Histories > Construction started, but not cutting yet
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #31  
Old Thu 30 August 2018, 03:59
ricdu34
Just call me: eric
 
gabian
France
quelques travaux ont été effectués meme si je n' ecris pas trop sur le forum.
Je ne peux y consacrer autant de temps que je veux et mon financement a été retardé ainsi j' avance doucement.
D' abord j' ai fait les rails,j' attends les cremailléres pour les finir.
Attached Images
File Type: jpg P1010741MD.jpg (109.4 KB, 249 views)
File Type: jpg P1010746MD.jpg (149.8 KB, 247 views)
File Type: jpg P1010792md.jpg (30.4 KB, 247 views)
File Type: jpg P1010795md.jpg (29.0 KB, 247 views)
Reply With Quote
  #32  
Old Thu 30 August 2018, 04:01
ricdu34
Just call me: eric
 
gabian
France
en anglais(désolé)
ome works have been done even if I do not write too much on the forum.
I can not spend as much time as I want and my funding has been delayed so I'm moving slowly.
First I made the rails, I wait for the racks to finish them.
Reply With Quote
  #33  
Old Thu 30 August 2018, 04:10
ricdu34
Just call me: eric
 
gabian
France
I also did the bevel on the Z plate
Photo1 the device without the plate
photo 2 in situation

j' ai aussi fait le biseau sur la plaque Z
Photo1 le dispositif sans la plaque
photo 2 en situation

I made some soldering points to join the plate with the device stuck in the table

J' ai fait quelques points de soudure pour solidariser la plaque avec le dispositif coincé dans la table etau
Attached Images
File Type: jpg P1010773md.jpg (71.4 KB, 246 views)
File Type: jpg P1010767md.jpg (132.1 KB, 247 views)
Reply With Quote
  #34  
Old Thu 30 August 2018, 04:16
ricdu34
Just call me: eric
 
gabian
France
j' ai aussi (mal )soudé le portique.
J' ai mal possitionné un embout et cela pose probléme pour le passage des cables.
J' ai aussi commençé la peinture
Attached Images
File Type: jpg P1010794md.jpg (68.2 KB, 245 views)
File Type: jpg P1010796.JPG (75.0 KB, 246 views)
File Type: jpg P1010797.JPG (63.1 KB, 247 views)
Reply With Quote
  #35  
Old Fri 07 September 2018, 04:53
ricdu34
Just call me: eric
 
gabian
France
this week I welded the car there on my marble in marble: D
the adventure goes on.
cette semaine j' ai soudé la voiture y sur mon marbre en marbre
l' aventure continue.
Attached Images
File Type: jpg P1010809md.jpg (75.7 KB, 209 views)
Reply With Quote
  #36  
Old Fri 14 September 2018, 07:31
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
It is nice table Eric. sembra fatto correttamente.
Reply With Quote
  #37  
Old Thu 15 July 2021, 03:47
ricdu34
Just call me: eric
 
gabian
France
En 2018,j' ai fabriqué toute la partie mécanique d ' une mechmate.
Vous pouvez retrouver toute l' historique ici : http://www.mechmate.com/forums/showthread.php?t=5633
Malheureusement mes affaires ont tourné en eau de boudin et suis resté quelques années sans tunes.
Comme tout a une fin, je me trouve en capacité de me remettre a investir dans cette machine.
En pur autodidacte (j' ai juste un bepc ) et ayant travaillé dans le restauration toute ma vie, je compense par une trés grande curiosité et une capacité a lire pendant des heures.
Je dois maintenant m' attaquer a la partie électronique et c' est ce qui me semble le plus dur a mon niveau.
Heureusement je sais qu' il y a des gens formidables et généreux sur les forums :smt023
Lorsque j' ai commandé le kit, j' ai opté pour une démultiplication des moteurs.
Voici les platines ,a gauche celle du Z, a droite les autres(par3 donc).

e pense les commander sur tridistribution. le ratio doit 1/3 ou 1/4 d' après ce que j' ai lu sur le forum mechmate mais je ne sais pas trop comment calculer la longueur de la courroie.
Pour les moteurs, j' ai opté pour des moteurs en boucle fermée.
Vu que j' ai une démultiplication, nema 34 en 4.5N.m sont suffisants.
Je pense prendre ce kit : https://www.ebay.fr/itm/114730018533...gAAOSwRihgUbCX
Il me faudra rajouter un quatrième moteur.
Toute réflexion bienvenue et je remercie d ' avance tous ceux qui m' aideront.


n 2018, I made all the mechanical part of a mechmate.
You can find the whole history herefor the french forum whose name is usinage.com) http://www.mechmate.com/forums/showthread.php?t=5633
Unfortunately my business turned out to be black pudding and went without money for a few years.
As everything has an end, I find myself able to get back to investing in this machine.
In pure autodidact (I have just a bepc) and having worked in the restoration all my life, I compensate by a very great curiosity and an ability to read for hours.
I now have to tackle the electronic part and this is what seems to me the hardest at my level.
Fortunately I know there are great and generous people on the forums: smt023
When I ordered the kit, I got a gear ratio for the motors.
Here are the decks, on the left that of the Z, on the right the others (par3 therefore).(to see on french part of the post)
I am thinking of ordering them on tridistribution. the ratio should 1/3 or 1/4 from what i read on the mechmate forum but not sure how to calculate the belt length.
For motors, I got for closed loop motors.
Since I have a reduction, nema 34 in 4.5N.m are sufficient.
I am thinking of taking this kit: https://www.ebay.fr/itm/114730018533...gAAOSwRihgUbCX
I will have to add a fourth engine.
Any thoughts welcome and I thank in advance all those who will help me.
Reply With Quote
  #38  
Old Thu 15 July 2021, 06:47
ricdu34
Just call me: eric
 
gabian
France
J ' ai bien sur quelques questions : que pensez vous de ce kit?
En particulier du controler.
Les cables pour les servos font 3 metres et, de tête pour le format de ma mechmate il faut 11 metres, comment fait'on?
Alimentation : AC24~70V or DC30~100V
Qu' est ce qui motive le choix entre AC ou DC?
Faut'il une alimentation toroidale?

I have a few questions: what do you think of this kit?
In particular the controler.
The cables for the servos are 3 meters long and, for the size of my mechmate, it takes 11 meters, how do we do it?
Power supply: AC24 ~ 70V or DC30 ~ 100V
What motivates the choice between AC or DC?
Do we need a toroidal power supply?
Thank you
Reply With Quote
  #39  
Old Fri 04 February 2022, 11:11
joscad49
Just call me: joscad
 
Angers
France
Bonjour,

Histoire d'échanger, je suis également un ptit français qui s'est lancé dans ce projet mechmate.
quelques vidéos et photo sur ma page facebook:
Teamfrog Fab lab

Au plaisir

Joscad
Reply With Quote
  #40  
Old Tue 15 February 2022, 03:02
ricdu34
Just call me: eric
 
gabian
France
Bonjour du sud.

Toujours en fabrication de mon coté, ça rame.
@+

Eric
Reply With Quote
  #41  
Old Sun 27 February 2022, 11:04
woodibe
Just call me: ibe
 
dakar
Senegal
Quote:
Originally Posted by joscad49 View Post
Bonjour,

Histoire d'échanger, je suis également un ptit français qui s'est lancé dans ce projet mechmate.
quelques vidéos et photo sur ma page facebook:
Teamfrog Fab lab

Au plaisir

Joscad
hello I am french carpenter and live in dakar senegal and I start construction MM is it possible to join you if I need thank you
Reply With Quote
  #42  
Old Sun 27 February 2022, 11:05
woodibe
Just call me: ibe
 
dakar
Senegal
Quote:
Originally Posted by ricdu34 View Post
Bonjour du sud.

Toujours en fabrication de mon coté, ça rame.
@+

Eric
hello I am french carpenter and live in dakar senegal and I start construction MM is it possible to join you if I need thank you
Reply With Quote
  #43  
Old Sun 27 February 2022, 14:26
woodibe
Just call me: ibe
 
dakar
Senegal
Quote:
Originally Posted by joscad49 View Post
Bonjour,

Histoire d'échanger, je suis également un ptit français qui s'est lancé dans ce projet mechmate.
quelques vidéos et photo sur ma page facebook:
Teamfrog Fab lab

Au plaisir

Joscad
IDEM im french and i start do build a MM
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New MechMate coming - Pacentro, Italy Fablab SPQwoRk Construction started, but not cutting yet 12 Wed 08 October 2014 14:11
My Mechmate coming up - India Manjeet Singh Construction started, but not cutting yet 13 Sat 24 May 2014 22:49
Table Coming Together! - QLD, Australia BooY Construction started, but not cutting yet 37 Fri 05 July 2013 18:34
Donkeys being cut in France! - Galgan, France bbreaker MechMates already cutting 71 Sun 17 August 2008 20:58
Cutting mdf doors, laser coming? #1 - Sri Lanka fabrica MechMates already cutting 192 Wed 23 January 2008 21:17


All times are GMT -6. The time now is 03:51.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.