|
|
|||||||
| Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
 |
|
|
Thread Tools |
|
#1
Fri 17 July 2009, 11:36
|
|||
|
|||
|
Flower Carvings and Skateboards! - Littleton, CO
|
|
#2
Fri 17 July 2009, 12:15
|
|||
|
|||
|
what are the bits you used and speed and time it took to complete
good one - did you have to sand it?
|
|
#3
Fri 17 July 2009, 12:41
|
|||
|
|||
|
Flower
Nice work!
|
|
#4
Fri 17 July 2009, 13:39
|
|||
|
|||
|
Justin,
That is very nice job.
|
|
#5
Fri 17 July 2009, 14:12
|
|||
|
|||
|
Well done & thanks for the tip !
|
|
#6
Fri 17 July 2009, 14:12
|
|||
|
|||
|
Very Nice, more info on finishing too!
|
|
#7
Fri 17 July 2009, 22:06
|
|||
|
|||
|
4 min rough pass w 1/4" ball nose, 26 min finishing pass w 1/8" ball nose. I was not contracted to do the finishing so I did not sand them. I only have these back because they want more and I need to match them up with the new ones. I think I did something like 60ipm on the rough and 50ipm on the finish.
|
|
#8
Sat 18 July 2009, 11:39
|
|||
|
|||
|
very beautiful and i like the staining
|
|
#9
Mon 13 June 2011, 23:43
|
|||
|
|||
|
Long Boards
Cut some prototype skateboards of a local company here.
|
|
#10
Fri 08 July 2011, 07:30
|
|||
|
|||
|
HPL desk for a vets office
I could not have done this job without my Mechmate.
|
|
#11
Fri 08 July 2011, 07:33
|
|||
|
|||
|
Pretty!
|
|
#12
Fri 08 July 2011, 08:17
|
|||
|
|||
|
Nice!
|
|
#13
Tue 12 July 2011, 13:43
|
|||
|
|||
|
is it MDF ? mélamine ?
|
|
#14
Fri 15 July 2011, 22:32
|
|||
|
|||
|
It is particle board with Laminate 2 sides. I had the laminate laid up by a local company here.
|
|
#15
Sun 17 July 2011, 20:39
|
|||
|
|||
|
Hi Justin
Did you carve a curve into both sides of the skateboards? What was the cutting sequence. Thanks David
|
|
#16
Wed 20 July 2011, 22:46
|
|||
|
|||
|
Hi David,
Are you talking about top and bottom curve? These boards are just flat. I will be doing some boards that will be laminated into a curve. That will be down the road. Justin
|
|
| Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| New Vacuum Table! #67 - Littleton, NC | salewis | MechMates already cutting | 137 | Sat 13 October 2012 05:54 |
| Workin for Beer #24 - Littleton, Colorado | lunaj76 | MechMates already cutting | 133 | Wed 09 May 2012 09:35 |
| 3D Carvings | javeria | The Show Room | 3 | Sun 30 May 2010 11:42 |
| Wrestling with Aspire on some carvings - Truckee, CA | inventall | MechMates already cutting | 46 | Fri 18 September 2009 17:33 |
