MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Common Assemblies & Parts > Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Wed 27 August 2014, 19:31
Duds
Just call me: Dale
 
Canberra
Australia
Off vertical drilling

Is it possible to drill off vertical using a ball shaped bit and moving in the x and y axis while drilling down through the z axis?
Assuming only 3 axis machine
Reply With Quote
  #2  
Old Wed 27 August 2014, 21:46
KenC
Just call me: Ken
 
Klang
Malaysia
Surely it can be done if you know your g-code well enough.
Reply With Quote
  #3  
Old Thu 28 August 2014, 03:45
lonestaral
Just call me: Al #114
 
Isarn
Thailand
Send a message via Skype™ to lonestaral
Do you mean 'Ramping' or 'Spiral cutting'

Yes you can.
Reply With Quote
  #4  
Old Thu 28 August 2014, 04:22
KenC
Just call me: Ken
 
Klang
Malaysia
I think he meant tilted straight holes.
Reply With Quote
  #5  
Old Thu 28 August 2014, 06:30
racedirector
Just call me: Bruce #122
 
New South Wales
Australia
But I would think that was not possible with just a vertical Z due to the straight bit.... or am I not thinking correctly? I take what you're trying to do is make a hole at an angle with a straight bit......
Reply With Quote
  #6  
Old Thu 28 August 2014, 06:38
Duds
Just call me: Dale
 
Canberra
Australia
I do mean tilted straight holes but not a straight bit. A ball bit. I can imagine that the angle is limited by the angle from the outside diameter of the ball and the shaft is the limitation of the angle.
Reply With Quote
  #7  
Old Thu 28 August 2014, 06:41
lonestaral
Just call me: Al #114
 
Isarn
Thailand
Send a message via Skype™ to lonestaral
Hole at an angle with a drill, put a wedge under the work, simple.
This follows the K.I.S.S. principle

As an alternative,
Tilt the Z axis, not simple.
Build a 4 or 5 axis machine, not simple (with knobs on).
Reply With Quote
  #8  
Old Thu 28 August 2014, 06:45
racedirector
Just call me: Bruce #122
 
New South Wales
Australia
Dale, that would probably but I can see the hole not being very deep. I would go with Al's idea, tilt the job and drill straight down, more room for a deeper hole.
Reply With Quote
  #9  
Old Thu 28 August 2014, 07:46
Duds
Just call me: Dale
 
Canberra
Australia
Thanks, great idea tilt the work and drill with Z. Or use a jig outside the machine. I want the machine to solve all my joinery but it's a just a tool with some specific strengths and weakness. Thanks for the reminder.
Reply With Quote
  #10  
Old Thu 28 August 2014, 09:06
smreish
Just call me: Sean - #5, 28, 58 and others
 
Orlando, Florida
United States of America
Dale,
Possible, as long as the hole diameter and the minor diameter of the ball bit shank is small enough to hit the lip on the entry area of the plunge cut.

It's like cutting and "uncut" lip on some parts.

---question--- are you trying to do something like a pocket hole like a KREG jig?
Reply With Quote
  #11  
Old Thu 28 August 2014, 09:08
ger21
Just call me: Ger
 
Detroit, MI
United States of America
Bruce, it'd just a straight line 3 axis move. However, the max angle would be limited, due to the tool being in the vertical orientation. Too much angle and the shank would hit the side of the hole.
Also, a ballnose bit isn't the best option for drilling.
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with Tabs ... it leaves vertical signs silverdog Troubleshooting 15 Wed 13 June 2012 00:27
2 X Parker HZR100 vertical actuators kentster The Market Place 0 Wed 17 August 2011 01:27
Space-saving vertical table Helge F. Holm 10. Base Table 8 Tue 01 September 2009 21:05
Vertical MechMate dullfig Archives 3 Thu 27 December 2007 21:19
Seating the Y-Car - V-Rollers' vertical adjustment slots fabrica 30. Y-Car 2 Sat 13 January 2007 21:15


All times are GMT -6. The time now is 00:21.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.