|
Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
|
Thread Tools |
#1
|
|||
|
|||
purpose of z axis gas spring
Hi Everyone
I've visited this site from time to time and drooled over the mechmate design . I'm thinking of building and have a question concerning the z-axis gas spring . what is it's function or purpose ? Thanks Bob |
#2
|
|||
|
|||
It acts as the counter weight for the z axis. If it is not there the full weight of the parts would be felt against the motor. Think of a draw bridge balance.
|
#3
|
|||
|
|||
Makes sense
Does it affect backlash in any way? |
#4
|
|||
|
|||
No it does not.
|
#5
|
|||
|
|||
Bob,
the side effect of having such a gas spring is that your hight will be set more accurately and your Z axis will move more smooth. The reason for this is that a stepper motor uses micro stepping and if a stepper motor is in a micro step, then it will loose strength as well. When the full weight is on the stepper motor, the stepper motor will go back (give or take) in a full step position because it doesn't have enough torque to hold it into a micro step. You will see that if you have no gas-spring and you move your Z up and down, you will only get full-step accuracy. Top of my head, that was 1/3 of a mm in my case. |
#6
|
|||
|
|||
Hi,
I have one more question about the gas spring. Is the gas spring extended in its normal (free/rest) state? As this would mean that when moving the Z gantry up, you would have to lift both the weigth of the slide, router, etc. + the pressure of the spring... Thanks in advance, Luc Last edited by buuk; Thu 06 October 2011 at 10:34.. |
#7
|
|||
|
|||
Luc,
the normal position of the gas-spring would be extended so it pushes against gravity. So it counter balances the wight of your spindle and your Z axis so your Z stepper doesn't have to work so hard. Also, when you buy your gas-spring, make sure it doesn't counter banker perfectly, but always have so push again or for gravity so your rack+pinion always make good contact Last edited by riesvantwisk; Thu 06 October 2011 at 10:50.. |
#8
|
|||
|
|||
When the z-slide is up then the spring is extended....when the z-slide is down then the spring is compressed.
The bottom of the gas spring is fixed to the y-car, the top of the gas spring is fixed to the z-slide. |
#9
|
|||
|
|||
Thanks for your quick replies.
I was thinking correctly about the forces, but made a mistake in which part was moving... stupid of me. But such things happen after a long day at work. Excuse me for this question... Thanks anyway! Luc |
Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Setting A-axis terminal as X2-axis in EMC2 | KenC | CNC motion control software | 2 | Wed 27 January 2010 05:40 |
Rotary axis (4th Axis) or Indexer software | smreish | Graphics & CAD | 0 | Tue 28 July 2009 06:02 |
FreeCAD - will be an open source general purpose 3D CAD modeler | isladelobos | Graphics & CAD | 0 | Sat 07 February 2009 04:25 |
Gas Spring : Compatible automotive gas spring | Nikonauts | 40. Z-Slide | 0 | Sat 03 January 2009 09:59 |
Umbilical Plate Purpose/Role | fabrica | 10. Base Table | 7 | Tue 20 February 2007 12:20 |