#121
|
|||
|
|||
This is my Zip Code in USA
TX 75065 |
#122
|
|||
|
|||
Laser Cut Parts
Ned, I just sent you a PM.
Only three sets left. |
#123
|
|||
|
|||
Been lurking too long. Shipping to 63385?
|
#124
|
|||
|
|||
Laser Cut Parts
Darren, I just sent you a PM.
Joe |
#125
|
|||
|
|||
Joe,
How often do you make these sets? I dont need one now but in about 3 months I will. Larry |
#126
|
|||
|
|||
Laser Cut Parts
Larry, sad to say that I will have sold my last set in a few days.
The person that I was dealing with to cut the parts was laid off due to the economy. I don't think the new guy is going to give me the same rate to cut and bend a set of parts. But I guess I could see. If I'm not mistaken. Castone is still selling laser cut parts. Joe |
#127
|
|||
|
|||
Anything left?
|
#128
|
|||
|
|||
And if you do, how do I pay?
|
#129
|
|||
|
|||
Quote:
|
#130
|
|||
|
|||
Alabama isn't dead yet.
Metalhead and I are working together to see if we can keep the parts flowing here in the US. We will be meeting with the local Laser/Fabricator guys hear this week to see if we can keep the set available at a affordable price. We will let you know what we find out. Joe |
#131
|
|||
|
|||
Good to hear that there is still life in Alabama! You served this community very well in the past.
|
#132
|
|||
|
|||
Joe kit available
I -just- got a kit from Joe that it turns out I am not going to use (I found an already-built machine for a great price).
The box is unopened. I'm in Portland, OR I'd like to get what it cost me, of course. Anyone interested? Greg |
#133
|
|||
|
|||
I talked with Joe and the Laser Parts company yesterday. I should have what I need in the next day or so to get a kit pulled together for sale. Just PM me if you are interested in a set of parts and when I get them pulled together I will let everyone know.
|
#134
|
|||
|
|||
Update on Laser Parts.
I had a test set ran to make sure the new folks met spec. I will touch the parts tomorrow to make sure they are good then I will order some sets. |
#135
|
|||
|
|||
Greg do you still have a kit from Joe? that you want to sell.
|
#136
|
|||
|
|||
I do indeed!
|
#137
|
|||
|
|||
Completed some parts for one of the members .
1x M1 30 224 Idler stub shaft. 6x M1 20 220 Bearing support base. PM me if you need a set. I have more. I am still tracking on the Laser Parts and they should start being ready soon !! |
#138
|
|||
|
|||
I am confused (and new) here. When someone supplies laser cut kits, what exactly is in the kit?
Thanks! Mike (also in Alabama) |
#139
|
|||
|
|||
S.Mike,
usually they are the parts found in ProfilesBends30Jun08.zip (see downloads ) However some people help others out with additional parts when they cannot do the work because the don't have the machines to make them, the above could be such a case when somebody doesn't have a lathe to make the Bearing support base. Ries |
#140
|
|||
|
|||
Here are some cool shots from a set of parts I made today (PM if you need a set) I am already checking a few long distant orders for folks.
I like the action shot of the Lathe boring the bushings. I did figure out the the next set will have the idler on the outside end and I will give a little more stock between the bushings. This lets me cut off the Idler then drill the holes and finish size the bushings on the blank. I can then go over and cut them off with the metal band saw. My parting skills in need of some work . !!! |
#141
|
|||
|
|||
Here are the parts test fitted. The idler is snug and will be pressed into the point it is flush with the outside of the idler shaft. I have to resist pressing the bearing on.... I won't say how I know they are hard to get back off !!!
Last edited by MetalHead; Thu 24 December 2009 at 19:26.. |
#142
|
|||
|
|||
Laser cut parts
S.Mike,
Ries was correct, I did not have a lathe and MetalHead(Mike) assisted me with this at a very good price and well machined parts. I purchased my Laser Cut Parts from Joe "Sweet Home Alabama" and was very pleased with the quality and price. I could not have built this without the technical help and assistance that this forum has. A lot of the builders on this site have the equipment needed to do most of the work, but it is geat when the same ones step up and help others. |
#143
|
|||
|
|||
Great pics Mike! and also inspiring... I want a lathe!!!
|
#144
|
|||
|
|||
Can someone point me to projects where the bed size was scaled down? I do not need (or have room) for 4x8. I am (hopefully) assuming that the gantry can remained unscaled (if width is mainained).
Mike |
#145
|
|||
|
|||
MechMate yeni versiyon cnc router çizimi yokmu? 2009-2010 çizimi bekliyoruz
|
#146
|
|||
|
|||
the new guy
Sir I am located at 36362 FORT RUCKER AL any sets left? Thank you for your time ERIC
Last edited by swordfish1382; Tue 19 January 2010 at 00:55.. |
#147
|
|||
|
|||
Sent you a PM - More sets will be ready in a few days.
|
#148
|
|||
|
|||
Hey Mike.
You forget me!!!! |
#149
|
|||
|
|||
No I haven't - Just trying to get time to figure out the customs forms. I will try to get through them this week.
|
#150
|
|||
|
|||
interested in laser cut parts
I am new to the forum and was interested in what the cost is for a set of the laser cut parts and what would shipping be to a 24153 zip code. Just want to say i have looked over the site for some time now and i am amazed at all the info that is available here. By the way has anyone done a video of the assy. of the mechmate and is it available.
Paul |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Laser Cut and Bent Parts - Europe | milkov | Profiled (laser cut) & bent steel plate | 33 | Fri 17 August 2012 13:13 |
Laser Cut and Bent Parts - India | dsingh82 | The Market Place | 10 | Thu 01 October 2009 04:14 |
Laser cut and formed parts | Castone | Profiled (laser cut) & bent steel plate | 5 | Sat 05 September 2009 00:40 |
Greetings all From United States | derekkest | Introduce yourself and start planning | 3 | Tue 09 June 2009 06:29 |
laser burnt pre-bent parts | ghostlx | Archives | 4 | Mon 22 September 2008 05:18 |