#1
|
|||
|
|||
In need of help getting started - Edinboro, PA
I posted an introduction that was also going to be my last due to insufficient funds to purchase the plans. I was very disappointed that this was going to be the case since this seemed to be the exact community and machine I was looking for.
I received encouraging emails from members in the MechMate community. My wife, being the the supportive wife she is, and I decided together that I could increase my funding to include the plans and as I am waiting for the budget allocation to be released I can now really get into researching the machine build along with getting prepared for it's operation. The question I have is really where to start. I am new to CNCing. I have a strong background in mathematics and computer software development. I have varying levels of skills in welding, electrical wiring and electronics. I have good carpentry skills. I have used AutoCAD in the past but only for simple drafting, nothing to complicated. I have already begun to just research on this site but if there is any additional books or resources you can point me to that would be greatly appreciated. Sorry for the long winded beginning but I am so excited to get started. Thanks and if I am posting incorrectly please let me know. Ted P.S. Thanks to all of you who encouraged me to stick with the MechMate I think it is going to work out great. |
#2
|
|||
|
|||
Glad to hear your going to dig in. Enjoy the read and we are looking forward to your build !!
|
#3
|
|||
|
|||
Ted, looking forward to your build!
|
#4
|
|||
|
|||
Ted,
Great that things worked out for you. Enjoy your build. I look forward to seeing your progress. |
#5
|
|||
|
|||
Ted,
Welcome to the community. You will find that we're a pretty "rag-tag fleet" of folks with varying degree's of use and interest. Some are experts, while others novice. I am certain you will fit in nicely. Best of luck. |
#6
|
|||
|
|||
Ted,
Glad you came back. The best advise I can give is to start reading the site. The more you read, the more questions that will crop up, and more reading starts to answer all of those questions that you didn't even know you needed to ask when you start. Once you are up and cutting you can start all over again learning the best ways to get the work done. This site is where the value is, you will find the plans, by supporting the site, were a bargain. Chuck |
#7
|
|||
|
|||
Welcome Ted!
|
#8
|
|||
|
|||
Welcome, and good luck with your build
|
#9
|
|||
|
|||
"...if there is any additional books or resources you can point me to that would be greatly appreciated."
Ted: Welcome to the MM mania. As for your question above, everything I needed I found in the forum, either already posted or answers to questions. Start there, you shouldn't need much, if anything, else. Good luck Joe #53 |
#10
|
|||
|
|||
Good Luck with the build. You will find this community very supportive, you have found the right place to begin your CNC adventure.
|
#11
|
|||
|
|||
Ted,
There are books on this forum in the form of builder threads. The advantage these threads have is that they have or are building the same machine you want to build. Better than any book. Read the threads of some completed builders. You will learn a lot. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rancho Cucamonga CA(Getting started) | tjlee337 | Introduce yourself and start planning | 11 | Fri 07 October 2011 06:54 |
Started on the electrical box - Canberra, AU | garymo | Construction started, but not cutting yet | 29 | Mon 30 May 2011 08:25 |
Just getting started.. couple questions... | Mountaincraft | 10. Base Table | 53 | Thu 02 September 2010 09:53 |
Getting Started - Karachi Pakistan | sohail | Introduce yourself and start planning | 29 | Fri 16 April 2010 07:47 |
Construction started - Greece | foinikas | Construction started, but not cutting yet | 20 | Thu 31 December 2009 10:13 |