MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 10 of 10
Search took 0.00 seconds.
Search: Posts Made By: Retief
Forum: Golden Resources Wed 29 October 2014, 08:11
Replies: 33
Views: 44,907
Posted By Retief
Thanks Normand - interesting Always nice to see...

Thanks Normand - interesting
Always nice to see solutions around board material
One would need straight edge/joining faces for this to work well - only corner joints
Expensive - 90$ for a chair
Forum: Golden Resources Tue 21 October 2014, 06:49
Replies: 33
Views: 44,907
Posted By Retief
Hi Hennie Yes, even to the big city's :) ...

Hi Hennie
Yes, even to the big city's :)
Retief
Forum: Golden Resources Mon 20 October 2014, 01:36
Replies: 33
Views: 44,907
Posted By Retief
Hi Alan I see you are just around the corner...

Hi Alan
I see you are just around the corner from me :)
The standard type T joint fitting in 6 and 9 mm are about R5.50 each (SA Rand). Corner extensions are about R2 each.
Retief
Forum: Golden Resources Mon 20 October 2014, 00:34
Replies: 33
Views: 44,907
Posted By Retief
Hi Guys Apart from this site...

Hi Guys
Apart from this site http://mypocketfactory.com/ offering designs and fittings, the fitting are available to fit a 6 and 9mm board.
Retief
Forum: Golden Resources Fri 17 October 2014, 04:44
Replies: 33
Views: 44,907
Posted By Retief
Hi Normand I have also been looking for a...

Hi Normand
I have also been looking for a strong joining methods and as a result started working on a CNC router friendly joining method and came up with a small plastic type clip-on type...
Forum: 70. Control Systems Fri 03 July 2009, 00:48
Replies: 9
Views: 11,037
Posted By Retief
Hi Gerald My 1st try was on J7 with the 5V+...

Hi Gerald
My 1st try was on J7 with the 5V+ powersupply
Now I have used your diagram and connector the SSR onto J81&2
I still need help with the mach pin setting?
Thanks
Retief
Forum: 70. Control Systems Thu 02 July 2009, 09:04
Replies: 9
Views: 11,037
Posted By Retief
Hi Goug Jip - my small router is running well -...

Hi Goug
Jip - my small router is running well - just need to get it to start and stop with my g-code:)
I use Vectric but will have to edit my code to get the start and stop command in before I send...
Forum: 70. Control Systems Thu 02 July 2009, 09:02
Replies: 9
Views: 11,037
Posted By Retief
Hi Gerald I need more help with the port and...

Hi Gerald
I need more help with the port and pin setting in Mach3
How do I tell Mach that I have the router on J8-1 and J8-2?
Thanks
Retief
Forum: 70. Control Systems Thu 02 July 2009, 08:48
Replies: 9
Views: 11,037
Posted By Retief
Hi Gerald Thanks for the reply will look into...

Hi Gerald
Thanks for the reply will look into this.

Domino 11 - The SSR are 5V and the power supply is 5.7V



Regards
Retief
Forum: 70. Control Systems Tue 30 June 2009, 08:13
Replies: 9
Views: 11,037
Posted By Retief
Router on and off - mach3

Hi....
I use a PMDX 122 and mach3 and would like to switch my Makita router on ( when program start) and off (when I am and the end of the code).

I have a solid state relay and 5.7 Volt...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -6. The time now is 03:14.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.