Forum: 60. Wiring & Cable Management
Fri 07 June 2013, 08:58
|
Replies: 221
Views: 225,170
|
Forum: MechMates already cutting
Wed 15 May 2013, 03:37
|
Replies: 53
Views: 52,940
|
Forum: Construction started, but not cutting yet
Thu 03 December 2009, 05:13
|
Replies: 24
Views: 29,589
New MM in Cape Town, South Africa
Eventually got my ducks in a row, and have made some decent progress on my MM.
Some of the table legs.
http://i92.photobucket.com/albums/l12/antonshart/PB100018.jpg
The Y Gantry....
|
Forum: Construction started, but not cutting yet
Wed 25 November 2009, 02:07
|
Replies: 59
Views: 75,888
|
Forum: 40. Z-Slide
Mon 23 November 2009, 00:29
|
Replies: 2
Views: 10,874
What can one do if it does not fit? I have...
What can one do if it does not fit? I have assembled the Y car without welding it, and tried fitting the spider in, and it was not going to go in without force. I measured the distance between the...
|
Forum: Construction started, but not cutting yet
Mon 23 November 2009, 00:29
|
Replies: 59
Views: 75,888
What can one do if it does not fit? I have...
What can one do if it does not fit? I have assembled the Y car without welding it, and tried fitting the spider in, and it was not going to go in without force. I measured the distance between the...
|
Forum: Motors & their mountings
Fri 31 July 2009, 04:45
|
Replies: 278
Views: 283,216
|
Forum: 702. Power Supplies
Mon 22 June 2009, 10:34
|
Replies: 134
Views: 159,896
|
Forum: 702. Power Supplies
Mon 22 June 2009, 10:33
|
Replies: 134
Views: 159,896
Gerald,
I see that the PK296A2A-Sg7.2 is 1.5...
Gerald,
I see that the PK296A2A-Sg7.2 is 1.5 mH indctance if wired unipolar, and 6 mH inductance if wired Bi-polar series. DO you guys all wire the motor in unipolar or Bi-polar? Am I right in...
|
Forum: MechMates already cutting
Mon 22 June 2009, 01:33
|
Replies: 99
Views: 151,224
Hi Matt (matty Zee),
Where did you get that...
Hi Matt (matty Zee),
Where did you get that spindle from? Internet perhaps?
What did you pay for it? WOuld be nice to replace the 2700 usd spindle option from the states with a cheaper option.
...
|
Forum: MechMates already cutting
Mon 22 June 2009, 01:26
|
Replies: 263
Views: 159,185
|
Forum: 80. Computer Hardware & Software
Fri 19 June 2009, 03:55
|
Replies: 80
Views: 90,266
Thanx guys's. I am blowing my budget a bit. Bit...
Thanx guys's. I am blowing my budget a bit. Bit hey, might as well score a new desktop out of the project. Are there any maximum specs recommended for the computer that runs the Mach 3 program, and...
|
Forum: 80. Computer Hardware & Software
Wed 17 June 2009, 21:52
|
Replies: 80
Views: 90,266
Gerald,
Will this Expresscard34 to Parralel...
Gerald,
Will this Expresscard34 to Parralel converter work with the PMDX-122 BOB?
http://www.synchrotech.com/products-expc/expresscard_34_parallel_printer_ieee1284_port_adapter_pcie_01.html
or...
|
Forum: Construction started, but not cutting yet
Mon 15 June 2009, 03:01
|
Replies: 24
Views: 29,589
|
Forum: Construction started, but not cutting yet
Mon 15 June 2009, 02:55
|
Replies: 24
Views: 29,589
|
Forum: Rails & Rollers
Mon 15 June 2009, 02:46
|
Replies: 50
Views: 137,848
|
Forum: Construction started, but not cutting yet
Sun 14 June 2009, 05:01
|
Replies: 24
Views: 29,589
Hello from Cape Town, when I am there!
Hi Guy's,
Absolutely the most comprehensive collection of info on building a damn good CNC machine. I have been going through the thread over the past few weeks, and everyday I am more impressed,...
|
Forum: 702. Power Supplies
Wed 10 June 2009, 05:44
|
Replies: 3
Views: 7,180
Transformer suppliers in Cape Town?
Hi Gerald,
Where in CT(if so) do you get the tranfromers made to order, and what specs would you recoomend ordering for a compromise between cooler running motors with reasonable torque...
|
Forum: Motors & their mountings
Tue 09 June 2009, 09:50
|
Replies: 278
Views: 283,216
|
Forum: 70. Control Systems
Tue 02 June 2009, 04:24
|
Replies: 14
Views: 37,478
Limit switch inputs
Hi Gerald,
Do the limit switches feed into the breakout board spare inputs, and are they used in the mach 3 program? :confused:
Anton
|
Forum: Construction started, but not cutting yet
Tue 02 June 2009, 04:10
|
Replies: 24
Views: 29,589
|
Forum: Construction started, but not cutting yet
Tue 02 June 2009, 04:05
|
Replies: 24
Views: 29,589
|
Forum: Construction started, but not cutting yet
Mon 01 June 2009, 10:57
|
Replies: 24
Views: 29,589
|
Forum: Construction started, but not cutting yet
Mon 01 June 2009, 03:30
|
Replies: 24
Views: 29,589
|
Forum: Cutting various materials - bit selection, feeds, speeds
Sun 31 May 2009, 12:57
|
Replies: 21
Views: 53,024
|