MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 21 of 21
Search took 0.00 seconds.
Search: Posts Made By: rocky2889
Forum: 50. Toolheads Wed 15 April 2009, 21:43
Replies: 5
Views: 10,345
Posted By rocky2889
Thanks!

Thanks!
Forum: 50. Toolheads Wed 15 April 2009, 13:03
Replies: 5
Views: 10,345
Posted By rocky2889
So is there anything I should do or don't for...

So is there anything I should do or don't for now? Should I just use as it until it need new bearing?

Thanks
Forum: 50. Toolheads Tue 14 April 2009, 23:56
Replies: 5
Views: 10,345
Posted By rocky2889
Finally My Spindle Is Running! Do I add grease?

Today is another major step to my CNC project. I have my spindle wiring and running. So far is only air running each time for around 10 minutes.

The spindle is an old new stock and the VFD goes...
Forum: 70. Control Systems Fri 03 April 2009, 10:27
Replies: 3
Views: 7,689
Posted By rocky2889
Ok, after recheck again the wiring and everything...

Ok, after recheck again the wiring and everything is should be. EXCEPT one thing I revere the pin number from X-- and X++ in the setup.

Also I have to lower the home reference speed to 15% of...
Forum: 70. Control Systems Sun 29 March 2009, 20:58
Replies: 3
Views: 7,689
Posted By rocky2889
I check out the limit switches today, all the...

I check out the limit switches today, all the switches are installed independent. I also checkout the Machsupport video on the subject of input and homing/limit.
Forum: 70. Control Systems Sat 28 March 2009, 20:00
Replies: 3
Views: 7,689
Posted By rocky2889
Setting up E-Stop and Limit Switches in Mach3

I try to understand E-stop and limit switches. Yes, I finish wire a small machine and installed limit switches.

Every time the gantry trips the limit switch and it also trigger the E-stop LED on...
Forum: CNC motion control software Mon 23 March 2009, 22:20
Replies: 6
Views: 18,250
Posted By rocky2889
I will be using Mach3 for the controller...

I will be using Mach3 for the controller software. I am hoping to get the machine test run early this week if everything as planned.

Thanks Gerald for the pointing the commend code and Kobus for...
Forum: CNC motion control software Sun 22 March 2009, 22:51
Replies: 6
Views: 18,250
Posted By rocky2889
Gcode for spiral circles.

I don't know this is the right thread to ask for this. I am looking for Gcode to draw spiral circles like this prefer in size about 24 to 36 inches diameter.

Thanks

Rocky
Forum: 701. Motor Drives Sat 07 March 2009, 22:29
Replies: 0
Views: 5,945
Posted By rocky2889
Electrical Phase Type Compatible

I would like to know the different type of electrical phase system.

Currently my building has 240/120 Delta 3 phase system.

I have a TB Woods VFD listed as 230V 3 Phase. I would like to know...
Forum: Motors & their mountings Tue 03 March 2009, 20:11
Replies: 2
Views: 5,977
Posted By rocky2889
I have a planetary gearbox hoping that I can use....

I have a planetary gearbox hoping that I can use. May be is too big anyway to use.

Thanks
Forum: Motors & their mountings Tue 03 March 2009, 14:14
Replies: 2
Views: 5,977
Posted By rocky2889
Where can I find a Motor Shaft Coupler for planetary gearbox?

I hope this is the right thread to post. Anyway I am looking for 19mm to 13m (3/4" to 1/2"). So far I cannot find in the SDP/SI website. May be anybody can help direct me to a site that I can order....
Forum: 70. Control Systems Sun 01 March 2009, 20:49
Replies: 10
Views: 11,147
Posted By rocky2889
I will give a test tomorrow when I have access to...

I will give a test tomorrow when I have access to the motor and drive at work. Thanks for the confirmation.
Forum: 50. Toolheads Sun 01 March 2009, 20:48
Replies: 2
Views: 7,280
Posted By rocky2889
The reason some of the panel is quite thick and...

The reason some of the panel is quite thick and it put much pressure on the router bit. It will be a smoother and faster cut if I use saw blade. It is just an idea at the moment. If I can find a...
Forum: 70. Control Systems Sun 01 March 2009, 09:14
Replies: 10
Views: 11,147
Posted By rocky2889
So if I add 470 ohm resistor to the last wiring I...

So if I add 470 ohm resistor to the last wiring I would be okay?

Thanks
Forum: 50. Toolheads Sun 01 March 2009, 08:20
Replies: 2
Views: 7,280
Posted By rocky2889
Swivel Head for z axis

So far I see only one post bring up the ideas for Tilt and Swivel head for Z axis. I am planing to adapt MM to use as panel saw besides router function. I don't need the tilt head to make the control...
Forum: 70. Control Systems Sat 28 February 2009, 15:57
Replies: 10
Views: 11,147
Posted By rocky2889
Ok, I reinsert the multiplier board back and use...

Ok, I reinsert the multiplier board back and use an external power supply is this right way to wire?
I connect the 5V- to the TERM. 6 and 5V+ to TERM.7.

TERM. 6 ----> Connect to the encoder label...
Forum: 701. Motor Drives Sat 28 February 2009, 14:45
Replies: 3
Views: 6,029
Posted By rocky2889
Thank you, you are the BEST.

Thank you, you are the BEST.
Forum: 70. Control Systems Sat 28 February 2009, 13:16
Replies: 10
Views: 11,147
Posted By rocky2889
Ok, I removed the multiplier board. Sorry I am...

Ok, I removed the multiplier board. Sorry I am little confused because the problem is the encoder with 5 wires and drive has 4 terminal.

This is what I did and bear with me if I am slow on this.
...
Forum: 70. Control Systems Sat 28 February 2009, 09:08
Replies: 10
Views: 11,147
Posted By rocky2889
Yes, I do have USDigital 500CPR encoder. May be I...

Yes, I do have USDigital 500CPR encoder. May be I give a try follow your direction.

But I do I like to able to use the multiplier. Please share information with me if anybody using this G340...
Forum: 70. Control Systems Fri 27 February 2009, 17:39
Replies: 10
Views: 11,147
Posted By rocky2889
Servo motor encoder wiring - is my diagram correct?

I am trying to wire and test a servo motor with G340 drive. The motor is for test run only. I have an USDigital encoder and it came with 5 wires like this.

#1-ground
#2-index
#3-A Channel...
Forum: 701. Motor Drives Fri 27 February 2009, 13:14
Replies: 3
Views: 6,029
Posted By rocky2889
Spindle Collet

I brought an used spindle "Elte TMPE3 12/2". I like to find out the size of the collet.
The only information engraved on the collet nut is "Schaublin EXE25 61-25720" I didn't see the ER25.

Do...
Showing results 1 to 21 of 21

 
Forum Jump

All times are GMT -6. The time now is 03:54.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.