MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: firebrick43
Forum: General - MM Build Sun 14 February 2010, 13:06
Replies: 96
Views: 94,217
Posted By firebrick43
Pablo, As a welder I understood what you where...

Pablo, As a welder I understood what you where getting at, I think you should of used the word "process" instead of "technique". Technique infers physical manipulation in some way.

The TIG...
Forum: General - MM Build Sat 13 February 2010, 08:54
Replies: 96
Views: 94,217
Posted By firebrick43
quote "(TIG is almost the same technique as MIG)"...

quote "(TIG is almost the same technique as MIG)"

This is a very misleading statement, especially since there are beginner welders here that might be confused.
Forum: General - MM Build Wed 18 November 2009, 10:09
Replies: 96
Views: 94,217
Posted By firebrick43
If Gas welding is acceptable then brazing is...

If Gas welding is acceptable then brazing is strong enough. Alot of race car, racing karts, and racing bicycles have been brazed with good success. Brazing has a higher tensile strength than steel,...
Forum: 70. Control Systems Mon 28 January 2008, 11:22
Replies: 333
Views: 337,600
Posted By firebrick43
Gerald, we run everything at higher voltages,...

Gerald, we run everything at higher voltages, either 24 or 120 volts, 5 volt probably would be a problem
Forum: 70. Control Systems Sat 26 January 2008, 00:15
Replies: 333
Views: 337,600
Posted By firebrick43
We use a lot of optical sensors at work on all of...

We use a lot of optical sensors at work on all of the material movement conveyors and robot cells. Their reliability is much less that the simple limit switches on all of our machine tools. The...
Forum: General - MM Build Sun 20 January 2008, 23:01
Replies: 96
Views: 94,217
Posted By firebrick43
Yes and no Gerald on the flux core migs. It has...

Yes and no Gerald on the flux core migs. It has been my observation that it is an increasing trend that heavy industry is actually going to flux core wire welders. These welders are very large,...
Forum: Archives Sun 20 January 2008, 15:01
Replies: 4
Views: 5,826
Posted By firebrick43
Thank you Gerald, Rare to see someone as...

Thank you Gerald,
Rare to see someone as honest, truthful, and humble as you are.
Forum: General - MM Build Sun 20 January 2008, 14:57
Replies: 96
Views: 94,217
Posted By firebrick43
I would like to make a few comments on welding. ...

I would like to make a few comments on welding.

Now as Gerald put it there is no critical welding on this machine so some of the following is moot. Most of the following is just therory and does...
Forum: Archives Sun 20 January 2008, 00:18
Replies: 4
Views: 5,826
Posted By firebrick43
Gerald, I would not sell yourself or the mechmate...

Gerald, I would not sell yourself or the mechmate short by calling it a "budget machine" I have heard my father say many time that there is three ways to do anything. Fast, inexpensively, or high...
Forum: General - MM Build Sat 19 January 2008, 23:24
Replies: 8
Views: 11,683
Posted By firebrick43
Hello, I agree with all of them but one and wish...

Hello, I agree with all of them but one and wish to add a few more.

"- Look as if painted before screws installed. ie. painted under washers. An unpainted washer gives proof of this. (Use zinc...
Forum: Archives Sat 19 January 2008, 19:32
Replies: 4
Views: 5,826
Posted By firebrick43
Plastics and alumiunum

Hello all,
I have spent alot of time looking and lurking, reading thru most of the post, learning as much as I can. Anyways, there is alot I like about the MechMate, especially it robustness that...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -6. The time now is 11:59.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.