Forum: MechMates already cutting
Sat 22 June 2013, 13:13
|
Replies: 257
Views: 153,660
|
Forum: MechMates already cutting
Sat 22 June 2013, 13:09
|
Replies: 428
Views: 201,723
Issue is not about being concentric (which is...
Issue is not about being concentric (which is also an issue) but you could drill a hole a little bit too large and when you put setscrews the pinion could wobble.
so drill on a lathe and ream the...
|
Forum: MechMates already cutting
Sun 10 March 2013, 01:26
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Sat 23 February 2013, 11:13
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Sat 16 February 2013, 08:34
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Sat 16 February 2013, 08:32
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Fri 15 February 2013, 16:10
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Fri 15 February 2013, 16:07
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Fri 15 February 2013, 15:49
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Mon 26 November 2012, 13:38
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Mon 26 November 2012, 12:55
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Mon 26 November 2012, 12:11
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Wed 05 September 2012, 14:44
|
Replies: 28
Views: 27,164
|
Forum: MechMates already cutting
Fri 17 August 2012, 12:09
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Wed 15 August 2012, 15:43
|
Replies: 271
Views: 194,634
|
Forum: MechMates already cutting
Mon 09 July 2012, 12:26
|
Replies: 241
Views: 187,078
|
Forum: MechMates already cutting
Mon 25 June 2012, 14:52
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Mon 25 June 2012, 14:47
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Mon 25 June 2012, 14:41
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Sun 03 June 2012, 04:27
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Sun 03 June 2012, 04:25
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Mon 14 May 2012, 14:39
|
Replies: 99
Views: 123,670
Axel,
first spindle will cut and second one...
Axel,
first spindle will cut and second one will V-groove.It is not possible to do that at the same time,I know that.My idea was to not waste time to change cutters for any sheet loaded on the...
|
Forum: MechMates already cutting
Mon 14 May 2012, 13:04
|
Replies: 99
Views: 123,670
Dear Dmitry,
my knowledge in this area are not...
Dear Dmitry,
my knowledge in this area are not great and that is one reason that my building goes so slow. I decided to finish all mechanical parts and then to devote to me unknown part of this...
|
Forum: MechMates already cutting
Sun 06 May 2012, 11:22
|
Replies: 99
Views: 123,670
|
Forum: MechMates already cutting
Sun 06 May 2012, 11:18
|
Replies: 99
Views: 123,670
|