Forum: MechMates already cutting
Sun 04 October 2009, 21:04
|
Replies: 117
Views: 75,244
Welcome Frallan,
Nice to see you on board......
Welcome Frallan,
Nice to see you on board...
Nice looking mill you did. You're way ahead of the game if you are already familiar with the concepts and parts. All you need is an enlargement...:)
|
Forum: MechMates already cutting
Sun 04 October 2009, 20:57
|
Replies: 22
Views: 20,144
|
Forum: MechMates already cutting
Sun 04 October 2009, 14:15
|
Replies: 22
Views: 20,144
Logo on
Hi guys...
I haven't been on the forum for several months... managed to get up and running in February, but had a death and several illnesses in my family so I put the beast (and many other things)...
|
Forum: General - MM Build
Thu 10 April 2008, 16:29
|
Replies: 19
Views: 24,713
Although I am just now getting ready to begin...
Although I am just now getting ready to begin building my MechMate, I would venture to guess that most of the "Quality" and speed from a much more expensive machine comes not due to the machine...
|
Forum: Archives
Mon 31 March 2008, 15:57
|
Replies: 10
Views: 11,522
|
Forum: Archives
Sat 08 March 2008, 09:37
|
Replies: 14
Views: 11,368
Funny...
Kinda reminds me of the hunter in...
Funny...
Kinda reminds me of the hunter in Colorado who shot a mule tail deer off a cliff. He, unfortunately, was standing at the bottom of the cliff when it fell... directly on top of him. ...
|
Forum: Archives
Tue 05 February 2008, 14:35
|
Replies: 25
Views: 16,958
|
Forum: Construction started, but not cutting yet
Fri 01 February 2008, 02:03
|
Replies: 10
Views: 10,366
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sun 30 December 2007, 21:44
|
Replies: 449
Views: 479,373
:)Apparently, the oriental motor guys thought...
:)Apparently, the oriental motor guys thought gears was a good way to go...since they are selling them, and I for one will be purchasing four of them...
One concern I do seem to recall in a post...
|
Forum: Rails & Rollers
Sun 30 December 2007, 21:30
|
Replies: 56
Views: 83,547
|
Forum: Construction started, but not cutting yet
Sat 22 December 2007, 10:52
|
Replies: 7
Views: 10,993
|
Forum: Construction started, but not cutting yet
Fri 21 December 2007, 16:45
|
Replies: 7
Views: 10,993
|
Forum: 702. Power Supplies
Sun 16 December 2007, 18:02
|
Replies: 16
Views: 23,753
|
Forum: 702. Power Supplies
Sat 15 December 2007, 16:48
|
Replies: 16
Views: 23,753
Sorry for your experience, Doug....
I just...
Sorry for your experience, Doug....
I just ordered my PS From Antek (600 VA) on Tuesday....received it today (Saturday). Everything went fine...except for the near hernia I got when I picked it...
|
Forum: 70. Control Systems
Thu 13 December 2007, 17:12
|
Replies: 79
Views: 107,395
Thanks Gerald...
You explained it very well. I...
Thanks Gerald...
You explained it very well. I just wish I'd taken up miniature jewelry work back when my fingers were still coordinated with my brain... it'd probably make my life easier when I...
|
Forum: 70. Control Systems
Thu 13 December 2007, 10:20
|
Replies: 79
Views: 107,395
Gerald...
I have been looking at your photos...
Gerald...
I have been looking at your photos above and on post #2, you mentioned that:
3. The empty terminals further right are for the shielded cables to the E-stops, Z-zero, etc. All Inputs....
|
Forum: MechMates already cutting
Tue 11 December 2007, 18:16
|
Replies: 489
Views: 408,173
|
Forum: Utility software
Tue 11 December 2007, 18:00
|
Replies: 3
Views: 11,514
|
Forum: Construction started, but not cutting yet
Mon 10 December 2007, 18:21
|
Replies: 61
Views: 131,754
|
Forum: 70. Control Systems
Sat 08 December 2007, 15:26
|
Replies: 16
Views: 17,164
|
Forum: 70. Control Systems
Sat 08 December 2007, 01:58
|
Replies: 16
Views: 17,164
|
Forum: MechMates already cutting
Mon 19 November 2007, 21:29
|
Replies: 171
Views: 122,642
|
Forum: Test Area for this forum
Tue 13 November 2007, 14:44
|
Replies: 41
Views: 50,228
|
Forum: Test Area for this forum
Mon 12 November 2007, 18:07
|
Replies: 41
Views: 50,228
Gerald/David...
I also have a Mac and have...
Gerald/David...
I also have a Mac and have never had a problem downloading from this site.
I just now downloaded ProfilesBends09Nov07.zip without any hitches.
David... you can email me and we...
|
Forum: MechMates already cutting
Fri 26 October 2007, 16:06
|
Replies: 205
Views: 235,586
|