Forum: MechMates already cutting
Wed 22 December 2021, 12:31
|
Replies: 124
Views: 157,370
Out with the Old-----In with the new.
Well time has come, as planned. My little 4x4 build is growing. After cutting close to 8-900 sheets of 1-inch Extira and plywood, and lots of bits and mistakes.:D.. I took it apart this week. Going...
|
Forum: About this Forum
Sun 22 March 2020, 15:33
|
Replies: 21
Views: 61,004
|
Forum: MechMates already cutting
Sun 22 March 2020, 09:28
|
Replies: 124
Views: 157,370
|
Forum: MechMates already cutting
Sat 21 March 2020, 06:24
|
Replies: 124
Views: 157,370
|
Forum: MechMates already cutting
Wed 11 March 2020, 05:58
|
Replies: 124
Views: 157,370
|
Forum: MechMates already cutting
Fri 22 November 2019, 05:21
|
Replies: 124
Views: 157,370
No, no filtration. This fan actually creates a...
No, no filtration. This fan actually creates a breeze through the box, and blows out.
I used aluminum tubing, and a screen mesh, as my heat sinks. Filtration filter was a thought. I may add it...
|
Forum: MechMates already cutting
Fri 08 November 2019, 16:17
|
Replies: 124
Views: 157,370
Updating Control Panel
Installing a new control panel, I got from Mike.
Purchased a set of Drill Hog Bits off ebay, to drill the holes.
So far so good. Looks way better than the 12x16x8 I had on it.:D
|
Forum: MechMates already cutting
Fri 07 June 2019, 17:23
|
Replies: 124
Views: 157,370
2.2kw spindleupdate
The spindle, I got online works well. It has out performed the 7518 Porter Cable significantly. A little hassle learning to solder the connection, to the motor, and wire the VFD, but not a large...
|
Forum: CNC motion control software
Fri 31 May 2019, 06:51
|
Replies: 3
Views: 20,562
|
Forum: Troubleshooting
Thu 30 May 2019, 07:03
|
Replies: 1
Views: 7,470
Mine is set at .081503. The software determined...
Mine is set at .081503. The software determined that for me. I could not find a preferred setting, based on weight. I suspect that it would also depend on the motor setup, you have configured. I use...
|
Forum: Introduce yourself and start planning
Sun 19 May 2019, 07:47
|
Replies: 7
Views: 16,666
|
Forum: MechMates already cutting
Tue 05 March 2019, 06:16
|
Replies: 124
Views: 157,370
|
Forum: MechMates already cutting
Tue 27 November 2018, 13:04
|
Replies: 124
Views: 157,370
|
Forum: MechMates already cutting
Wed 21 November 2018, 17:41
|
Replies: 124
Views: 157,370
2.2 Kw Spindle Finally
Just got a 2.2 kw water cooled spindle and vfd for an upgrade. The Porter Cable worked fine for plywood and long curves. We'll see how it goes.
Happy Turkey Day to all tomorrow.
|
Forum: MechMates already cutting
Fri 19 October 2018, 07:15
|
Replies: 109
Views: 149,532
|
Forum: MechMates already cutting
Fri 19 October 2018, 07:07
|
Replies: 124
Views: 157,370
|
Forum: Construction started, but not cutting yet
Fri 14 September 2018, 07:31
|
Replies: 42
Views: 57,147
|
Forum: Motors & their mountings
Mon 28 May 2018, 21:44
|
Replies: 4
Views: 12,093
|
Forum: MechMates already cutting
Thu 24 May 2018, 07:00
|
Replies: 197
Views: 270,817
|
Forum: MechMates already cutting
Sun 20 May 2018, 22:10
|
Replies: 124
Views: 157,370
|
Forum: MechMates already cutting
Sun 20 May 2018, 16:30
|
Replies: 197
Views: 270,817
|
Forum: MechMates already cutting
Sat 19 May 2018, 07:47
|
Replies: 124
Views: 157,370
If anyone is using the PMDX134 board, and...
If anyone is using the PMDX134 board, and experience problems, that do not make sense. Replace the 25 pin ribbon cable. Maybe it will solve your problems, as it did mine.
I believe this, to also be...
|
Forum: MechMates already cutting
Sat 19 May 2018, 07:43
|
Replies: 197
Views: 270,817
|
Forum: MechMates already cutting
Fri 18 May 2018, 15:26
|
Replies: 197
Views: 270,817
|
Forum: MechMates already cutting
Thu 17 May 2018, 11:07
|
Replies: 74
Views: 97,963
|