Forum: 55. Dust Management
Sun 17 October 2021, 02:50
|
Replies: 1
Views: 5,450
Have you seen this project? ...
Have you seen this project?
https://www.youtube.com/watch?v=IF8U8nd5oSM
It would be very easy to make a manual positioning dust shoe, why would you like to automate it?
|
Forum: MechMates already cutting
Sun 05 September 2021, 07:48
|
Replies: 17
Views: 17,483
I did not think about the point of gravity...
I did not think about the point of gravity building mine :(
The motor is a closed-Loop Stepper motor 142MM 9n.m 1280 oz.in 6A, the ball screw is a 2010 (10mm/turn)
Tests already made with a...
|
Forum: General - MM Build
Mon 01 June 2020, 07:15
|
Replies: 6
Views: 21,272
IMHO the original free donation was a good...
IMHO the original free donation was a good choice, I made a donation greater than the requested fee. I'm sure every builder did the donation, but I don't know how many fees from people who just...
|
Forum: Construction started, but not cutting yet
Tue 08 May 2018, 03:56
|
Replies: 42
Views: 55,334
inverter power supply are ok, better a single...
inverter power supply are ok, better a single bigger one than one for each motor ... but a simple transformer rectifier and condenser is better than the above. Stepper drivers, those kits have the...
|
Forum: Construction started, but not cutting yet
Tue 08 May 2018, 03:40
|
Replies: 42
Views: 55,334
|
Forum: Construction started, but not cutting yet
Tue 08 May 2018, 03:31
|
Replies: 42
Views: 55,334
|
Forum: Miscellaneous / General / Whatever / Catchall
Sun 24 September 2017, 04:02
|
Replies: 6
Views: 14,390
|
Forum: Miscellaneous / General / Whatever / Catchall
Fri 22 September 2017, 05:12
|
Replies: 6
Views: 14,390
|
Forum: CAM
Tue 05 September 2017, 04:08
|
Replies: 3
Views: 31,822
|
Forum: Miscellaneous / General / Whatever / Catchall
Tue 05 September 2017, 04:05
|
Replies: 6
Views: 14,390
Steel cutting at high speed
https://www.youtube.com/watch?v=i61cy7aAi8A&pbjreload=10
Since Mechmate is a stronger shopbot ... :-)
give a look at this CAM too :-)...
|
Forum: 80. Computer Hardware & Software
Fri 14 July 2017, 05:11
|
Replies: 6
Views: 15,619
uhmm ... I think pololu are a bit underpowered...
uhmm ... I think pololu are a bit underpowered for a nema34 ... if you want to try that solution, use at least the drv8825 which have a maximum output of 2.5 Amp pay attention to the specification,...
|
Forum: 80. Computer Hardware & Software
Wed 05 July 2017, 15:06
|
Replies: 6
Views: 15,619
|
Forum: Introduce yourself and start planning
Fri 28 April 2017, 01:55
|
Replies: 6
Views: 11,359
|
Forum: MechMates already cutting
Sun 23 April 2017, 14:46
|
Replies: 100
Views: 230,600
the whole set of pictures:...
the whole set of pictures: https://www.facebook.com/photo.php?fbid=10211309040497638&set=a.10211308929854872.1073741910.1109014643&type=3&theater
|
Forum: MechMates already cutting
Sun 23 April 2017, 14:39
|
Replies: 100
Views: 230,600
|
Forum: CNC motion control software
Wed 19 April 2017, 11:20
|
Replies: 8
Views: 20,206
|
Forum: CNC motion control software
Wed 19 April 2017, 08:29
|
Replies: 8
Views: 20,206
Great work on Auto Zero tool. :-)
I have one...
Great work on Auto Zero tool. :-)
I have one question I could not find thr answer myself, I use a laser cross-hair pointer to set the X-Y workpiece start point. In Mach3 I added a button and two...
|
Forum: 80. Computer Hardware & Software
Mon 17 April 2017, 10:07
|
Replies: 6
Views: 15,619
GRBL firmware and bCNC
I am testing GRBL Arduino firmare with bCNC control software https://github.com/vlachoudis/bCNC/wiki ... Kitchen Table testing for the moment :) ... but I am realy impressed on haw the open source is...
|
Forum: MechMates already cutting
Mon 17 April 2017, 09:22
|
Replies: 556
Views: 531,261
Hi guys :-) ... same old story on the v-wheels...
Hi guys :-) ... same old story on the v-wheels against linear guides :-) I remenber and understood what Gerald pointed out once ... Linear guides are much more complicated to mount, if you don't get...
|
Forum: MechMates already cutting
Sun 15 January 2017, 14:25
|
Replies: 8
Views: 12,012
|
Forum: MechMates already cutting
Sun 15 January 2017, 12:44
|
Replies: 8
Views: 12,012
|
Forum: MechMates already cutting
Sun 01 January 2017, 13:34
|
Replies: 6
Views: 11,354
|
Forum: MechMates already cutting
Wed 21 December 2016, 00:13
|
Replies: 100
Views: 230,600
|
Forum: MechMates already cutting
Wed 14 December 2016, 06:29
|
Replies: 100
Views: 230,600
|
Forum: MechMates already cutting
Sat 20 August 2016, 09:37
|
Replies: 241
Views: 187,094
|