Forum: About this Forum
Tue 24 May 2011, 08:26
|
Replies: 203
Views: 203,955
|
Forum: 10. Base Table
Tue 14 December 2010, 04:29
|
Replies: 28
Views: 54,116
:)
...
:)
http://www.mechmate.com/forums/attachment.php?attachmentid=3427&stc=1&d=1232845354:)
http://www.mechmate.com/forums/showthread.php?p=20816&postcount=116
|
Forum: 40. Z-Slide
Thu 28 October 2010, 04:41
|
Replies: 6
Views: 14,157
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sun 12 September 2010, 06:44
|
Replies: 449
Views: 484,907
|
Forum: MechMates already cutting
Thu 02 September 2010, 09:01
|
Replies: 551
Views: 508,912
|
Forum: MechMates already cutting
Mon 09 August 2010, 09:32
|
Replies: 1,586
Views: 1,029,657
|
Forum: MechMates already cutting
Tue 20 April 2010, 07:37
|
Replies: 1,586
Views: 1,029,657
Hi Kobus:
...
Hi Kobus:
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=1028
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=94963
Hope that helps :)
|
Forum: CNC motion control software
Sun 27 December 2009, 07:09
|
Replies: 62
Views: 75,842
Orotemo,
What driver are you using?
I...
Orotemo,
What driver are you using?
I use "Smile" :) (http://www.lolata.com.br/Smile/) and there are 04 boards to control each of the motors. In the X1 motor connection is correct but the...
|
Forum: MechMates already cutting
Sat 04 July 2009, 08:59
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Sat 04 July 2009, 08:37
|
Replies: 178
Views: 122,370
Regarding the noise: a tip from a friend in...
Regarding the noise: a tip from a friend in Brazil, EMC2 setup to use the Gecko drive (although using a Smile :)) and the noise decreased by 70% ... was not a mechanical problem ... but still not as...
|
Forum: MechMates already cutting
Sat 04 July 2009, 08:21
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Sat 04 April 2009, 21:52
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Fri 03 April 2009, 17:16
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Fri 03 April 2009, 17:13
|
Replies: 178
Views: 122,370
Hi,
I made a fault with you. :o
When I...
Hi,
I made a fault with you. :o
When I cut the entry and exit of air from my control desk, were the parts.
1 - Rectangle: 265 mm x 140 mm
2 - Circle - 108 mm
Cutting speed:...
|
Forum: MechMates already cutting
Mon 30 March 2009, 15:17
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Sat 28 March 2009, 17:00
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Thu 26 March 2009, 16:25
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Wed 25 March 2009, 22:14
|
Replies: 178
Views: 122,370
Thanks Mike,
The speed at which it makes...
Thanks Mike,
The speed at which it makes less noise is between 9.000mm/min and 16.000mm/min.
Below 6.000mm/min there is a huge noise.
I hope that the reduction belt (to be 2,66:1) noise...
|
Forum: MechMates already cutting
Wed 25 March 2009, 19:45
|
Replies: 178
Views: 122,370
Nills and Mike,
Yes my problem is X, but in...
Nills and Mike,
Yes my problem is X, but in only one of four rack.
Mike, I believe there is misalignment or screw loose.
Moving with the hand (without engine coupled) noise appears in only...
|
Forum: MechMates already cutting
Wed 25 March 2009, 19:31
|
Replies: 95
Views: 98,276
|
Forum: 40. Z-Slide
Fri 13 March 2009, 17:21
|
Replies: 86
Views: 104,190
|
Forum: MechMates already cutting
Tue 24 February 2009, 19:54
|
Replies: 178
Views: 122,370
|
Forum: MechMates already cutting
Sat 21 February 2009, 14:16
|
Replies: 178
Views: 122,370
There is no obstruction.
I have tried...
There is no obstruction.
I have tried everything I could imagine, before asking.
Replaces original rack for another (that left the Z axis) and noise is the same.
I am lost.
Appears no...
|
Forum: MechMates already cutting
Sat 21 February 2009, 09:20
|
Replies: 178
Views: 122,370
|
Forum: 70. Control Systems
Sat 21 February 2009, 09:06
|
Replies: 25
Views: 20,979
I traded my PC a few days.
Is an AMD...
I traded my PC a few days.
Is an AMD Athlon 64 X2 5000 to 2.6 Ghz 4GB.
See the photo that the parallel port (purple highlight the left)
Out the cable of an old PC and turned on the...
|