MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Reload this Page Search Results
Register Options Profile Last 1 | 3 | 7 Days Today's Posts

Showing results 1 to 8 of 8
Search took 0.00 seconds. Search: Posts Made By: nes_t326
Forum: MechMates already cutting Mon 18 December 2023, 09:47
Replies: 0
Views: 1,931
Posted By nes_t326
A CNC Plasma Cutter Mechmate

After more than a decade after I posted my plan of building a Mechmate in the forum, we have built a CNC Plasma Cutter Mechmate !
https://www.youtube.com/watch?v=aLUPsdr4kJ4
Forum: Introduce yourself and start planning Mon 18 December 2023, 09:34
Replies: 15
Views: 12,485
Posted By nes_t326
http://www.youtube.com/watch?v=aLUPsdr4kJ4 I...

http://www.youtube.com/watch?v=aLUPsdr4kJ4
I finally bite the bullet / took the risk of building a Mechmate Plasma cutter and it is now cutting ! . . . it was 2011 when I dreamed of owning a...
Forum: Introduce yourself and start planning Fri 09 September 2011, 14:59
Replies: 15
Views: 12,485
Posted By nes_t326
A tight budget has led me to this road :( But...

A tight budget has led me to this road :(
But reading from this forum and surfing a lot of other sites, I have read that new IC tech digitally driving analog circuitry can deliver maximum power even...
Forum: Introduce yourself and start planning Fri 09 September 2011, 01:35
Replies: 15
Views: 12,485
Posted By nes_t326
After reading and a tight budget, I'll start with...

After reading and a tight budget, I'll start with the following drive system:

1.) NEMA 34/126mm Stepper Motor, 4 Wire, Bipolar, 5.4 Amp Rated Current, 5.8 mH Phase Inductance and 7.4 N-m Holding...
Forum: Introduce yourself and start planning Sun 07 August 2011, 23:32
Replies: 15
Views: 12,485
Posted By nes_t326
I try to grasp only the basic of these...

I try to grasp only the basic of these electrical/electronics . . .

Please advice on the integration and performance of the following:

Motor: UIM86-A stepper motor
Driver: ...
Forum: Introduce yourself and start planning Fri 05 August 2011, 08:44
Replies: 15
Views: 12,485
Posted By nes_t326
Thanks Mike, 'first glance at the MM and the...

Thanks Mike, 'first glance at the MM and the people around it is an inspiration for someone new to the world of CNC's like me. Cheers!
Forum: Introduce yourself and start planning Fri 05 August 2011, 05:23
Replies: 15
Views: 12,485
Posted By nes_t326
Thanks John#26, just started sourcing stepper...

Thanks John#26, just started sourcing stepper motors here in the Middle East and South East Asia particularly in Singapore and Philippines.
Forum: Introduce yourself and start planning Fri 05 August 2011, 04:45
Replies: 15
Views: 12,485
Posted By nes_t326
Quest for a CNC stopped ! . . . - Philippines

I am working here in Saudi Arabia and got a deep interest on CNC's, have surfed a lot of sites and my quest stopped upon seeing the MM table which suite my requirements, presently on the Planning...
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -6. The time now is 11:38.

Contact Us - www.mechmate.com - Archive - Top

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.