Forum: Troubleshooting
Fri 19 November 2021, 17:33
|
Replies: 0
Views: 2,883
Giving back to great MM community
Resently I noticed a length accuracy issue. Whatever length I wanted to have it is always shorter for about 1.5mm or so. Couldn't figure out what is the problem. Checked coordinate from file, looked...
|
Forum: 50. Toolheads
Sun 04 November 2018, 06:35
|
Replies: 1
Views: 7,098
|
Forum: MechMates already cutting
Sat 15 September 2018, 08:08
|
Replies: 454
Views: 441,326
|
Forum: MechMates already cutting
Sat 15 September 2018, 06:29
|
Replies: 454
Views: 441,326
|
Forum: MechMates already cutting
Thu 13 September 2018, 05:56
|
Replies: 454
Views: 441,326
|
Forum: MechMates already cutting
Wed 12 September 2018, 09:53
|
Replies: 454
Views: 441,326
Make sure you have RF chokes installed at the...
Make sure you have RF chokes installed at the output of the VFD. VFDs are big source of RF interference. I removed RF chokes/toroid cores from some old scrap monitors. You will see them as a thick...
|
Forum: The Show Room
Tue 28 March 2017, 20:53
|
Replies: 9
Views: 20,223
|
Forum: MechMates already cutting
Tue 17 January 2017, 13:34
|
Replies: 454
Views: 441,326
|
Forum: Miscellaneous / General / Whatever / Catchall
Sun 01 January 2017, 23:15
|
Replies: 18
Views: 25,627
|
Forum: Troubleshooting
Sun 06 November 2016, 18:13
|
Replies: 11
Views: 19,058
So, here is update.
As mentioned before,...
So, here is update.
As mentioned before, first I tighten the timing belts. Think, it changed something. Then, when I cut those lines I realized that their width is not 1/2" but a bit more. I can...
|
Forum: Troubleshooting
Fri 04 November 2016, 18:55
|
Replies: 11
Views: 19,058
|
Forum: Troubleshooting
Tue 01 November 2016, 18:42
|
Replies: 11
Views: 19,058
|
Forum: Troubleshooting
Tue 01 November 2016, 15:29
|
Replies: 11
Views: 19,058
|
Forum: Troubleshooting
Tue 01 November 2016, 11:54
|
Replies: 11
Views: 19,058
Acceleration is very conservative. I can not...
Acceleration is very conservative. I can not recall now but I am not that crazy about the speed. I cut were cut at about 120-150 IPM. Test lines, as well, same speed. Depth is about 1/16".
Error...
|
Forum: Troubleshooting
Mon 31 October 2016, 16:03
|
Replies: 11
Views: 19,058
Pulling whatever is left of hair and no solution
Hello fellow MechMaters,
Started cutting some circles, and noticed they are not the size they are suppose to be. Circle is real circle, not ellipse, but it is a bit short in diameter. Tried to...
|
Forum: MechMates already cutting
Sat 20 August 2016, 10:03
|
Replies: 241
Views: 188,811
|
Forum: Cutting various materials - bit selection, feeds, speeds
Thu 11 August 2016, 05:09
|
Replies: 9
Views: 19,065
|
Forum: Cutting various materials - bit selection, feeds, speeds
Sun 07 August 2016, 23:54
|
Replies: 9
Views: 19,065
|
Forum: Cutting various materials - bit selection, feeds, speeds
Sat 06 August 2016, 06:13
|
Replies: 9
Views: 19,065
Making 700+ holes?
I will have to make about 700+ holes in baltic birch 1" thick. Hole size is 1/2" and 3/4". How would you do it considering the number of holes? Drilling or spiral cutting? Feeds and speeds?
...
|
Forum: Human Interface Devices (HID's)
Thu 04 August 2016, 12:34
|
Replies: 4
Views: 38,539
|
Forum: General - MM Build
Wed 30 March 2016, 10:15
|
Replies: 258
Views: 405,150
|
Forum: General - MM Build
Wed 30 March 2016, 05:51
|
Replies: 258
Views: 405,150
|
Forum: General - MM Build
Tue 29 March 2016, 05:41
|
Replies: 258
Views: 405,150
To save out backs
http://www.workbenchmagazine.com/mai...tle-video.html
http://www.workbenchmagazine.com/mai...0-caddy03.html
|
Forum: General - MM Build
Fri 15 January 2016, 06:37
|
Replies: 258
Views: 405,150
|