Forum: Troubleshooting
Thu 08 July 2021, 08:31
|
Replies: 1
Views: 3,723
how to slave x motors
I have a shobot prt 96.
when i tried to run this morning it jump the rail found out x motors moving in
the same direction. need advise in resetting the slave . is there a step by step ...
|
Forum: Troubleshooting
Fri 19 February 2021, 10:47
|
Replies: 2
Views: 5,334
|
Forum: Troubleshooting
Wed 17 February 2021, 12:48
|
Replies: 2
Views: 5,334
Zero touch place not connecting
I am running mach3 BOB PMDX-122 Gecko drive G203v.
been running for a few years with no problems.
just had a problem popped up i went to zero to the table top using the zero plate
when i ran...
|
Forum: 701. Motor Drives
Fri 12 September 2014, 12:02
|
Replies: 17
Views: 27,047
Hi Bradm
the problem turned out to be the...
Hi Bradm
the problem turned out to be the breakout board i call PMDX tech support and they talk we through it
j3 was not working
i had j4 spare so i put the z on it
well i now have a spare...
|
Forum: 701. Motor Drives
Mon 08 September 2014, 10:28
|
Replies: 17
Views: 27,047
|
Forum: 701. Motor Drives
Sun 07 September 2014, 19:19
|
Replies: 17
Views: 27,047
problem is back
its no more an intermittent problem z now does not move.
its not the motor as i have swapped supply and motor works
i took a voltage reading on the z g203 between step and common and got 1.36v
on...
|
Forum: 701. Motor Drives
Fri 25 July 2014, 08:53
|
Replies: 17
Views: 27,047
|
Forum: 701. Motor Drives
Thu 24 July 2014, 08:47
|
Replies: 17
Views: 27,047
|
Forum: 701. Motor Drives
Thu 24 July 2014, 06:54
|
Replies: 17
Views: 27,047
Gecko 203v intermittent fault
Gecko 203v intermittent fault
The problem i am having is with my z azis when i switch my cnc in the morning, and try to move the z azis
using the page up page down buttons no movement.
...
|
Forum: 60. Wiring & Cable Management
Wed 27 November 2013, 05:21
|
Replies: 221
Views: 223,867
|
Forum: 60. Wiring & Cable Management
Tue 26 November 2013, 17:40
|
Replies: 221
Views: 223,867
|
Forum: 60. Wiring & Cable Management
Tue 26 November 2013, 13:26
|
Replies: 221
Views: 223,867
ebay cable
Can anyone tell me if this cable is any good.
thanks paul.
http://www.ebay.com/itm/Shielded-Cable-Wire-4-x-18Ga-Stepper-Motor-CNC-Router-/160632659191
|
Forum: 60. Wiring & Cable Management
Tue 26 November 2013, 13:25
|
Replies: 221
Views: 223,867
eby cable
Can anyone tell me if this cable is any good.
thanks paul.
http://www.ebay.com/itm/Shielded-Cable-Wire-4-x-18Ga-Stepper-Motor-CNC-Router-/160632659191
|
Forum: 70. Control Systems
Tue 29 October 2013, 19:02
|
Replies: 4
Views: 11,463
What was wrong with your Gecko G203v? dont...
What was wrong with your Gecko G203v? dont really know what the problem was with my
g203v one of my x motor just stopped working. i checked the fuse and it was ok.
replaced and everything is...
|
Forum: 70. Control Systems
Fri 25 October 2013, 14:34
|
Replies: 4
Views: 11,463
courious about this
i am running mach 3 using geckodrive G203v
normally when i power up i hear a thump that comes from the stepped motor. i took this as normal.
i then had a faulty G203 which i replaced not i get...
|
Forum: 701. Motor Drives
Mon 30 September 2013, 17:10
|
Replies: 5
Views: 11,810
Suspect gecko G 203V problem
I am running a shopbot using Gecko drives i notice today one of my x drive
motors was not running.
after swaping x drive inputs connectors i got the motor to work.
both of my x drives are...
|
Forum: 70. Control Systems
Thu 24 May 2012, 11:27
|
Replies: 14
Views: 21,814
|
Forum: 70. Control Systems
Thu 24 May 2012, 06:49
|
Replies: 14
Views: 21,814
Smooth stepper
am courious what advantage i will get using a smooth stepper unit from warp9 tech design
I am using mach3
gecko g203
pmdx-122 breakout board. stepper motor 9412ktg-a6497 Oriental Motor
...
|
Forum: 50. Toolheads
Thu 29 September 2011, 04:26
|
Replies: 47
Views: 79,309
coolant
thanks for the information.
i washed it out and replaced the antifreeze so i will how it goes
thanks
|
Forum: 50. Toolheads
Tue 27 September 2011, 05:18
|
Replies: 47
Views: 79,309
coolant
I need to get some information on the correct collant to use.
i live in the tropics where the temperture never goes under 75 deg.
should the antifreeze be used full strength or 50/50
at the...
|
Forum: 50. Toolheads
Tue 27 April 2010, 10:16
|
Replies: 28
Views: 28,380
|
Forum: 50. Toolheads
Tue 27 April 2010, 06:35
|
Replies: 28
Views: 28,380
|
Forum: 70. Control Systems
Thu 01 April 2010, 11:03
|
Replies: 8
Views: 7,573
|
Forum: 70. Control Systems
Thu 01 April 2010, 09:36
|
Replies: 8
Views: 7,573
Hi Brad
thanks for your reply
i do not have...
Hi Brad
thanks for your reply
i do not have the tuning to fast problem any more. and the computer i replaced is the same
as the one that crashed.
so i do not think that i am overdriving the...
|
Forum: 70. Control Systems
Thu 01 April 2010, 09:29
|
Replies: 8
Views: 7,573
|