Forum: 50. Toolheads
Wed 15 April 2009, 21:43
|
Replies: 5
Views: 10,509
|
Forum: 50. Toolheads
Wed 15 April 2009, 13:03
|
Replies: 5
Views: 10,509
|
Forum: 50. Toolheads
Tue 14 April 2009, 23:56
|
Replies: 5
Views: 10,509
Finally My Spindle Is Running! Do I add grease?
Today is another major step to my CNC project. I have my spindle wiring and running. So far is only air running each time for around 10 minutes.
The spindle is an old new stock and the VFD goes...
|
Forum: 70. Control Systems
Fri 03 April 2009, 10:27
|
Replies: 3
Views: 7,853
|
Forum: 70. Control Systems
Sun 29 March 2009, 20:58
|
Replies: 3
Views: 7,853
|
Forum: 70. Control Systems
Sat 28 March 2009, 20:00
|
Replies: 3
Views: 7,853
Setting up E-Stop and Limit Switches in Mach3
I try to understand E-stop and limit switches. Yes, I finish wire a small machine and installed limit switches.
Every time the gantry trips the limit switch and it also trigger the E-stop LED on...
|
Forum: CNC motion control software
Mon 23 March 2009, 22:20
|
Replies: 6
Views: 19,053
I will be using Mach3 for the controller...
I will be using Mach3 for the controller software. I am hoping to get the machine test run early this week if everything as planned.
Thanks Gerald for the pointing the commend code and Kobus for...
|
Forum: CNC motion control software
Sun 22 March 2009, 22:51
|
Replies: 6
Views: 19,053
Gcode for spiral circles.
I don't know this is the right thread to ask for this. I am looking for Gcode to draw spiral circles like this prefer in size about 24 to 36 inches diameter.
Thanks
Rocky
|
Forum: 701. Motor Drives
Sat 07 March 2009, 22:29
|
Replies: 0
Views: 6,045
Electrical Phase Type Compatible
I would like to know the different type of electrical phase system.
Currently my building has 240/120 Delta 3 phase system.
I have a TB Woods VFD listed as 230V 3 Phase. I would like to know...
|
Forum: Motors & their mountings
Tue 03 March 2009, 20:11
|
Replies: 2
Views: 6,070
|
Forum: Motors & their mountings
Tue 03 March 2009, 14:14
|
Replies: 2
Views: 6,070
|
Forum: 70. Control Systems
Sun 01 March 2009, 20:49
|
Replies: 10
Views: 11,362
|
Forum: 50. Toolheads
Sun 01 March 2009, 20:48
|
Replies: 2
Views: 7,451
|
Forum: 70. Control Systems
Sun 01 March 2009, 09:14
|
Replies: 10
Views: 11,362
|
Forum: 50. Toolheads
Sun 01 March 2009, 08:20
|
Replies: 2
Views: 7,451
Swivel Head for z axis
So far I see only one post bring up the ideas for Tilt and Swivel head for Z axis. I am planing to adapt MM to use as panel saw besides router function. I don't need the tilt head to make the control...
|
Forum: 70. Control Systems
Sat 28 February 2009, 15:57
|
Replies: 10
Views: 11,362
|
Forum: 701. Motor Drives
Sat 28 February 2009, 14:45
|
Replies: 3
Views: 6,125
|
Forum: 70. Control Systems
Sat 28 February 2009, 13:16
|
Replies: 10
Views: 11,362
Ok, I removed the multiplier board. Sorry I am...
Ok, I removed the multiplier board. Sorry I am little confused because the problem is the encoder with 5 wires and drive has 4 terminal.
This is what I did and bear with me if I am slow on this.
...
|
Forum: 70. Control Systems
Sat 28 February 2009, 09:08
|
Replies: 10
Views: 11,362
|
Forum: 70. Control Systems
Fri 27 February 2009, 17:39
|
Replies: 10
Views: 11,362
|
Forum: 701. Motor Drives
Fri 27 February 2009, 13:14
|
Replies: 3
Views: 6,125
Spindle Collet
I brought an used spindle "Elte TMPE3 12/2". I like to find out the size of the collet.
The only information engraved on the collet nut is "Schaublin EXE25 61-25720" I didn't see the ER25.
Do...
|