Forum: The Market Place
Fri 16 June 2017, 16:00
|
Replies: 2
Views: 10,709
|
Forum: The Market Place
Mon 03 April 2017, 15:05
|
Replies: 2
Views: 10,709
#16 NW Indiana For Sale
#16 For Sale. Has only been used as a hobby machine. Has cut a lot of different projects over the years. 50"x 120" build. 3 to 1 gear reduction all axis.
Build Thread:...
|
Forum: MechMates already cutting
Tue 25 March 2014, 19:25
|
Replies: 216
Views: 216,710
Congrats on #116. I remember when I completed...
Congrats on #116. I remember when I completed mine, a hundred machines before you. Let the dust fly.
Mines more of a hobby machine, buts makes some nice side cash when you need it. My wife still...
|
Forum: 70. Control Systems
Tue 03 April 2012, 20:09
|
Replies: 333
Views: 343,819
|
Forum: 70. Control Systems
Tue 03 April 2012, 19:56
|
Replies: 333
Views: 343,819
|
Forum: 70. Control Systems
Tue 03 April 2012, 18:45
|
Replies: 333
Views: 343,819
|
Forum: 70. Control Systems
Tue 03 April 2012, 17:56
|
Replies: 333
Views: 343,819
|
Forum: 70. Control Systems
Tue 03 April 2012, 17:21
|
Replies: 333
Views: 343,819
Looking for a little help.
I have proxys 1...
Looking for a little help.
I have proxys 1 for each axis. And I bought the winford relay board Sean talked about in post 49. My problem is I can get each to work independantly, but when I try to...
|
Forum: MechMates already cutting
Fri 26 November 2010, 20:13
|
Replies: 137
Views: 112,860
|
Forum: MechMates already cutting
Fri 14 May 2010, 04:35
|
Replies: 61
Views: 83,839
|
Forum: MechMates already cutting
Sat 06 March 2010, 15:08
|
Replies: 152
Views: 153,847
|
Forum: MechMates already cutting
Fri 22 January 2010, 10:26
|
Replies: 63
Views: 50,226
|
Forum: MechMates already cutting
Tue 19 January 2010, 19:51
|
Replies: 1,586
Views: 1,026,667
|
Forum: CAM
Fri 15 January 2010, 16:29
|
Replies: 19
Views: 27,750
|
Forum: CAM
Thu 14 January 2010, 19:48
|
Replies: 19
Views: 27,750
I'm using Aspire with my Mechmate. I also...
I'm using Aspire with my Mechmate. I also upgraded from V-carve pro. Aspire takes it to the next level with it's 3d modeling. Aspire is a lot more bang for the buck than Artcam or Mastercam. But each...
|
Forum: MechMates already cutting
Tue 12 January 2010, 04:46
|
Replies: 62
Views: 65,330
I was happy about the plates and design. I was...
I was happy about the plates and design. I was unhappy with the local hardware store. I don't have a very good selection of fasteners near me. So I had to do a little brain storming to make things...
|
Forum: MechMates already cutting
Sun 10 January 2010, 18:16
|
Replies: 62
Views: 65,330
Upgrade-3 to 1 Transmissions installed
Working on and off this afternoon, I managed to assemble and install the 3 to 1 belt drive gear plates I bought from Castone (Leo). Everything seems to move and jog well. Now I can't wait to do some...
|
Forum: MechMates already cutting
Mon 07 December 2009, 19:46
|
Replies: 25
Views: 26,836
|
Forum: MechMates already cutting
Mon 30 November 2009, 20:53
|
Replies: 43
Views: 34,625
Congrats Leo,
Don't worry what it looks...
Congrats Leo,
Don't worry what it looks like. The dustier, the better. I used to Vac mine off every use, but now just when someone new wants to see it. I try to keep the rails and rollers clean.
...
|
Forum: Profiled (laser cut) & bent steel plate
Thu 08 October 2009, 04:44
|
Replies: 191
Views: 203,925
|
Forum: MechMates already cutting
Wed 07 October 2009, 16:05
|
Replies: 89
Views: 69,598
|
Forum: MechMates already cutting
Wed 23 September 2009, 04:46
|
Replies: 131
Views: 111,311
|
Forum: The Show Room
Wed 23 September 2009, 04:46
|
Replies: 6
Views: 11,150
|
Forum: MechMates already cutting
Tue 15 September 2009, 19:14
|
Replies: 46
Views: 40,215
Minimum System Requirements
The Aspire,...
Minimum System Requirements
The Aspire, VCarve Pro, Cut3D, PhotoVCarve and Cut2D software products will all run on virtually all home PC's and do not require any special hardware or graphics card....
|