Forum: 20. Gantry
Fri 27 September 2019, 12:14
|
Replies: 2
Views: 28,173
See this post...
See this post (http://www.mechmate.com/forums/showthread.php?p=3630&postcount=40) for a pic of the "stop blocks" which are screwed to the carriages, and they hit the end-stops at the end of the rails
|
Forum: Miscellaneous / General / Whatever / Catchall
Tue 06 March 2018, 00:52
|
Replies: 12
Views: 33,057
Sitting at home at last - no more commuting!
Greetings to all!
Finally stopped being a wage-earner and commuter end of last month. Now dabble in some stuff from home. Having fun with WineLadder (http://www.wineladder.co.za). Got time for 4...
|
Forum: Graphics & CAD
Fri 28 October 2016, 13:13
|
Replies: 21
Views: 82,149
I like that DraftSight, set to Classic mode,...
I like that DraftSight, set to Classic mode, gives me the same look and feel as AutoCAD. Having used AutoCAD daily for about 30 years, I use it without thinking. I have successfully taught AutoCAD to...
|
Forum: Graphics & CAD
Thu 27 October 2016, 13:10
|
Replies: 21
Views: 82,149
|
Forum: Graphics & CAD
Wed 26 October 2016, 23:26
|
Replies: 21
Views: 82,149
|
Forum: Graphics & CAD
Fri 21 October 2016, 00:20
|
Replies: 21
Views: 82,149
|
Forum: Graphics & CAD
Thu 20 October 2016, 00:17
|
Replies: 21
Views: 82,149
|
Forum: MechMates already cutting
Sun 13 September 2015, 09:34
|
Replies: 454
Views: 457,560
|
Forum: MechMates already cutting
Sat 29 August 2015, 00:42
|
Replies: 479
Views: 552,453
Unfortunately for the people who enjoy...
Unfortunately for the people who enjoy traditional woodwork, a CNC router is going to earn the most (or easiest) income while cutting boards, and most of these boards are synthetic "wood".
Our...
|
Forum: MechMates already cutting
Fri 28 August 2015, 00:56
|
Replies: 479
Views: 552,453
|
Forum: The Market Place
Fri 21 August 2015, 13:05
|
Replies: 5
Views: 16,980
Mark's machine was more fully described here:...
Mark's machine was more fully described here: http://www.mechmate.com/forums/showthread.php?t=2537
Luke, the PM system here does not discriminate for low post counts, but the recipient may have...
|
Forum: MechMates already cutting
Fri 07 August 2015, 03:30
|
Replies: 778
Views: 512,155
Another one-stop moulding shop...
Another one-stop moulding shop http://www.smooth-on.com/ (represented out here by www.amtcomposites.co.za (http://www.amtcomposites.co.za))
|
Forum: General - MM Build
Thu 06 August 2015, 09:57
|
Replies: 154
Views: 308,950
|
Forum: General - MM Build
Thu 06 August 2015, 01:46
|
Replies: 154
Views: 308,950
|
Forum: General - MM Build
Sun 19 July 2015, 09:28
|
Replies: 154
Views: 308,950
It is all a compromise between:
- speed /...
It is all a compromise between:
- speed / acceleration (you might be looking only at these and calling it performance)
- flex /chatter / repeatable positioning under varying loads (a massive part...
|
Forum: General - MM Build
Sun 19 July 2015, 05:44
|
Replies: 154
Views: 308,950
|
Forum: Test Area for this forum
Tue 14 July 2015, 09:23
|
Replies: 7
Views: 38,876
|
Forum: 702. Power Supplies
Fri 26 June 2015, 13:18
|
Replies: 134
Views: 163,030
Removed Reference Post
You might also be able...
Removed Reference Post
You might also be able to run even less voltage without lost steps . . . . just as you are able to get around in a small car without bumping into anyone. It proves nothing.
...
|
Forum: 702. Power Supplies
Fri 26 June 2015, 09:23
|
Replies: 134
Views: 163,030
Removed Reference Post
I would add 20% to...
Removed Reference Post
I would add 20% to voltages calculated by Mariss, which takes the 48V to 58V.
The shorter motor has much more chance of loosing steps because it has less torque....
|
Forum: 702. Power Supplies
Thu 25 June 2015, 22:51
|
Replies: 134
Views: 163,030
|
Forum: Construction started, but not cutting yet
Wed 24 June 2015, 23:37
|
Replies: 69
Views: 104,393
|
Forum: Construction started, but not cutting yet
Tue 23 June 2015, 11:16
|
Replies: 12
Views: 23,846
|
Forum: Construction started, but not cutting yet
Sat 20 June 2015, 23:43
|
Replies: 232
Views: 240,265
|
Forum: MechMates already cutting
Tue 09 June 2015, 01:00
|
Replies: 735
Views: 493,510
|
Forum: Introduce yourself and start planning
Tue 02 June 2015, 07:34
|
Replies: 11
Views: 13,909
|