Forum: Introduce yourself and start planning
Tue 12 April 2022, 05:58
|
Replies: 5
Views: 5,211
|
Forum: MechMates already cutting
Tue 06 October 2020, 09:09
|
Replies: 134
Views: 171,829
|
Forum: MechMates already cutting
Wed 09 September 2020, 04:49
|
Replies: 56
Views: 83,659
|
Forum: MechMates already cutting
Wed 09 September 2020, 04:34
|
Replies: 56
Views: 83,659
Hi Mark
The machine is working verry well...
Hi Mark
The machine is working verry well right now. I have found that the problem is the efficiency of the diy shielding that I have done before. in fact, a I used aluminum tape for all the wires...
|
Forum: MechMates already cutting
Wed 19 August 2020, 14:14
|
Replies: 56
Views: 83,659
Hi Mark
Thank's a lot for you reply.
I...
Hi Mark
Thank's a lot for you reply.
I am using a linear power supply providing about 60v and enough power (watts) to feed all the 4 servos. And I am also separating the servos supply groud...
|
Forum: MechMates already cutting
Fri 14 August 2020, 07:48
|
Replies: 56
Views: 83,659
Somme update to my build
Hi comunnity
I want to add somme update to my build:
- First I was working with a 600w router that was very noisy, but It was working fine with small dept of cutting and slower speeds.
-...
|
Forum: MechMates already cutting
Tue 14 April 2020, 10:16
|
Replies: 56
Views: 83,659
Hi All
I would like to thank you all for the...
Hi All
I would like to thank you all for the encouragement.
For Mark : I am very glad that I have chosen the acorn+Clearpath setup,
I would recommend for everyone who is willing to use these...
|
Forum: 10. Base Table
Mon 02 March 2020, 15:13
|
Replies: 6
Views: 24,996
Hi
I don't think it would be a problem. You...
Hi
I don't think it would be a problem. You just need to be careful when placing the linear rails and you should leave some clearance with more the 1/8 inch for mounting the racks.
Good luck
|
Forum: MechMates already cutting
Mon 02 March 2020, 11:26
|
Replies: 56
Views: 83,659
She's cutting :-)
Hi dear Mechmate community
I would like to annouce that we have made the first job on the machine today. It was wondefull feeling.
Indeed the machine is not 100% complete, but we needed to see...
|
Forum: MechMates already cutting
Thu 29 August 2019, 23:50
|
Replies: 56
Views: 83,659
Hi Ted
I am running them in series. Each one...
Hi Ted
I am running them in series. Each one of them is rated to deliver 12V on nominal current and 21V open circuit. So in series, I get 42V.
When running one of the servos I get 20 V in each...
|
Forum: MechMates already cutting
Sat 24 August 2019, 18:52
|
Replies: 56
Views: 83,659
|
Forum: MechMates already cutting
Fri 23 August 2019, 03:51
|
Replies: 56
Views: 83,659
Hi all
Sorry for not being able to post in...
Hi all
Sorry for not being able to post in the last months.
Here is an update of the build !
- The painting job was done last month.
- Adaptation plates were designed and tested
-...
|
Forum: MechMates already cutting
Fri 14 June 2019, 05:42
|
Replies: 134
Views: 171,829
|
Forum: MechMates already cutting
Thu 30 May 2019, 05:49
|
Replies: 56
Views: 83,659
|
Forum: MechMates already cutting
Tue 28 May 2019, 10:26
|
Replies: 56
Views: 83,659
Rack attached to rail
Hi
Some progress :)
- The Y rail rack is attached
- X rails racks in pgrogress
I also ordered the following :
- 2 x Clearpath Servos CPM-SDSK-2310S-RQN for the X-axis
|
Forum: MechMates already cutting
Mon 20 May 2019, 00:52
|
Replies: 134
Views: 171,829
|
Forum: MechMates already cutting
Mon 20 May 2019, 00:34
|
Replies: 56
Views: 83,659
Hi all,
Finally, I am back again to work in...
Hi all,
Finally, I am back again to work in the machine, so I taught I would share some of the advancement.
--> I found a solution for the previous problem of the damaging that was happening...
|
Forum: Introduce yourself and start planning
Sun 19 May 2019, 23:36
|
Replies: 7
Views: 15,855
|
Forum: MechMates already cutting
Sat 30 March 2019, 08:14
|
Replies: 56
Views: 83,659
|
Forum: MechMates already cutting
Sat 30 March 2019, 01:06
|
Replies: 56
Views: 83,659
Gantry nearly completed
Hi all,
Thanks a lot, Robert, Mark and Mike for the precious advise. And sorry for being late to respond.
I bought four good quality bar clumps and did the gantry twist correction as can be...
|
Forum: MechMates already cutting
Wed 27 February 2019, 11:50
|
Replies: 56
Views: 83,659
Thanks a lot Robert for the quick reply,
...
Thanks a lot Robert for the quick reply,
I thought that the clamps like BESSY are only good for woodworking not for metal now i will look for some good quality ones, i think they are available...
|
Forum: MechMates already cutting
Wed 27 February 2019, 09:57
|
Replies: 56
Views: 83,659
Gantry nearly completed
Hi all
Here are some updates about the build.
Unfortunately, we have the problem of a twisted gantry. As shown in the pictures above one of the four edges of the gantry is about 5mm far from...
|
Forum: MechMates already cutting
Sun 30 December 2018, 16:29
|
Replies: 56
Views: 83,659
HI Mark,
I had no experience in welding...
HI Mark,
I had no experience in welding before starting this project and I managed to complete the table without difficulty (I have just watched some instructional youtube videos).
For the...
|
Forum: MechMates already cutting
Sat 22 December 2018, 03:01
|
Replies: 56
Views: 83,659
|
Forum: MechMates already cutting
Fri 21 December 2018, 09:36
|
Replies: 56
Views: 83,659
x and y rails
Hi all,
I wanted to share some advancement on the project :)
- We bought 9 meters of Racks
- Made the Excentric bushings from 12mm blots
- Finished the assembly of skate grinder
- Finished...
|