Forum: The Market Place
Tue 15 May 2012, 10:11
|
Replies: 62
Views: 103,182
|
Forum: Motors & their mountings
Sun 21 November 2010, 07:26
|
Replies: 17
Views: 24,235
Dave,
Sorry,to hijack your build thread by...
Dave,
Sorry,to hijack your build thread by asking all these Drive Plate Questions. :o
Started a new thread
While gathering information about the MetalHead Drive Plates in the Common...
|
Forum: Motors & their mountings
Sun 21 November 2010, 07:05
|
Replies: 17
Views: 24,235
|
Forum: Motors & their mountings
Sat 20 November 2010, 09:25
|
Replies: 17
Views: 24,235
Belt Drive Plates
For the MetalHead Gear Drive Plates where and how do the FR8 flange bearings come into play?
I figure you need to use 2 FR8 bearings for each of the four drives required in the Mechmate design...
|
Forum: The Market Place
Thu 30 September 2010, 10:38
|
Replies: 0
Views: 5,022
40% router bits for two days even Onsurd
Just passing this info onto the Mechmate group. I got this offer by email today.
40% off cutters from MSC Big Book but only for two days.
thurs sept 30th day and friday oct 1st use this code...
|
Forum: 50. Toolheads
Thu 26 August 2010, 11:29
|
Replies: 37
Views: 45,397
Gerald,
Good point about the air ports...
Gerald,
Good point about the air ports getting clogged up. I ask the ebay seller about the air-cooled spindle. I have not yet received an answer. I did find this post on CNC Zone.
"Bob...
|
Forum: 50. Toolheads
Tue 24 August 2010, 20:16
|
Replies: 37
Views: 45,397
Thanks Danilo!
After reading more about...
Thanks Danilo!
After reading more about HuanYang VFD quality I will look to purchase a better quality VFD locally.
I am concerned about the cost of running 2.2kw - 4kw spindles from a single...
|
Forum: 50. Toolheads
Tue 24 August 2010, 14:09
|
Replies: 37
Views: 45,397
|
Forum: 50. Toolheads
Mon 16 August 2010, 08:54
|
Replies: 4
Views: 9,023
|
Forum: Graphics & CAD
Mon 07 June 2010, 18:43
|
Replies: 1
Views: 8,645
Deskproto v5 hobby license special offer!
http://www.deskproto.com/download/pr_hobby-license_2010.htm
I have used this products demo version. For $295 seems like quite a deal for all the functions offered. Full functional version but not...
|
Forum: 10. Base Table
Thu 31 December 2009, 04:39
|
Replies: 14
Views: 24,504
|
Forum: 10. Base Table
Wed 30 December 2009, 10:40
|
Replies: 14
Views: 24,504
I may be able to get a 4'x8' x1/2" PVC plastic...
I may be able to get a 4'x8' x1/2" PVC plastic sheet for $95. I think this sheet normally retails for around $400. What do you think about using this PVC for the support board and then mdf for the...
|
Forum: General - MM Build
Wed 30 September 2009, 09:19
|
Replies: 94
Views: 95,479
I am very impressed with how well this item...
I am very impressed with how well this item removes heavy rust. I know most of you have seen these in action but this was my first time using one. Screw it on to an angle grinder and go.
On the...
|
Forum: General - MM Build
Wed 16 September 2009, 09:38
|
Replies: 25
Views: 25,620
|
Forum: General - MM Build
Tue 15 September 2009, 13:51
|
Replies: 25
Views: 25,620
Fastners Metric or Standard does it matter
Humor me…..
I am going though the steps to determine a bom for fasteners.
I would like to go with inch bolts over metric for cost savings.
Have I exhausted all the consideration necessary to...
|
Forum: 10. Base Table
Mon 30 July 2007, 08:04
|
Replies: 118
Views: 162,586
|
Forum: 10. Base Table
Sun 29 July 2007, 15:47
|
Replies: 118
Views: 162,586
|