Forum: MechMates already cutting
Wed 10 May 2023, 20:32
|
Replies: 551
Views: 503,737
|
Forum: MechMates already cutting
Thu 10 June 2021, 20:00
|
Replies: 17
Views: 17,457
|
Forum: MechMates already cutting
Fri 15 January 2021, 07:03
|
Replies: 479
Views: 530,915
|
Forum: MechMates already cutting
Tue 19 November 2019, 18:33
|
Replies: 216
Views: 214,464
Are your steppers reading ok with a meter? You...
Are your steppers reading ok with a meter? You definitely have a problem with the B set of windings on two different drives. This leads me to believe that two drives are bad which is unlikely at the...
|
Forum: MechMates already cutting
Tue 19 November 2019, 18:26
|
Replies: 216
Views: 214,464
|
Forum: MechMates already cutting
Wed 01 May 2019, 17:32
|
Replies: 984
Views: 677,753
|
Forum: MechMates already cutting
Wed 16 January 2019, 16:19
|
Replies: 479
Views: 530,915
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Mon 31 December 2018, 11:01
|
Replies: 449
Views: 470,221
|
Forum: MechMates already cutting
Mon 20 August 2018, 05:51
|
Replies: 454
Views: 434,785
|
Forum: MechMates already cutting
Thu 16 August 2018, 04:26
|
Replies: 454
Views: 434,785
|
Forum: MechMates already cutting
Wed 15 August 2018, 21:26
|
Replies: 454
Views: 434,785
|
Forum: MechMates already cutting
Wed 15 August 2018, 11:33
|
Replies: 454
Views: 434,785
|
Forum: MechMates already cutting
Mon 13 August 2018, 04:22
|
Replies: 454
Views: 434,785
|
Forum: MechMates already cutting
Thu 19 July 2018, 19:42
|
Replies: 74
Views: 95,416
Working in maintenance we found that Goodyear...
Working in maintenance we found that Goodyear belts held up the longest to the abuse of heat and work stress. They were acquired by Continental a few years back but still make a quality belt.
If...
|
Forum: Introduce yourself and start planning
Thu 19 July 2018, 19:13
|
Replies: 3
Views: 9,103
|
Forum: MechMates already cutting
Thu 19 July 2018, 19:10
|
Replies: 72
Views: 81,727
|
Forum: MechMates already cutting
Thu 19 July 2018, 19:07
|
Replies: 74
Views: 95,416
|
Forum: MechMates already cutting
Sun 15 July 2018, 10:34
|
Replies: 454
Views: 434,785
|
Forum: Troubleshooting
Sun 03 June 2018, 10:54
|
Replies: 5
Views: 13,195
Also most routers are universal motors. These...
Also most routers are universal motors. These are not meant to run forever like induction motors. They have a limited lifespan. For instance your standard wet dry vac uses a universal motor. ...
|
Forum: CNC motion control software
Sun 03 June 2018, 10:49
|
Replies: 8
Views: 16,601
No worries, we all have troubles at time, my...
No worries, we all have troubles at time, my suggestion is to learn more about your machine and setup. It makes life much easier. Most of us have built the machines so we learned as we went. You...
|
Forum: 10. Base Table
Sun 03 June 2018, 10:46
|
Replies: 3
Views: 12,957
Taper is technically stronger if the sizes are...
Taper is technically stronger if the sizes are the same however it adds other items to deal with if you choose to bolt through using a bolt and nut. If you choose to tap the hole it is not an issue,...
|
Forum: CNC motion control software
Sun 03 June 2018, 10:40
|
Replies: 8
Views: 16,601
if you can still open the old mach3 on the...
if you can still open the old mach3 on the computer you use to use, verify every screen. Sounds like something did not transfer. Also be sure to write down or screenshot all setup data when you are...
|
Forum: CNC motion control software
Sun 03 June 2018, 10:29
|
Replies: 8
Views: 16,601
check here...
check here https://www.machsupport.com/forum/index.php?topic=6957.0
|
Forum: CNC motion control software
Thu 31 May 2018, 18:26
|
Replies: 8
Views: 16,601
You seem stressed, I work in industrial...
You seem stressed, I work in industrial maintenance and understand this is frustrating however a clear sequence of events is helpful. CNC knowledge on a this level is probably more then you have...
|
Forum: CNC motion control software
Thu 31 May 2018, 18:12
|
Replies: 8
Views: 16,601
|