Forum: Troubleshooting
Thu 01 January 2015, 12:29
|
Replies: 4
Views: 13,677
|
Forum: Troubleshooting
Wed 31 December 2014, 14:09
|
Replies: 4
Views: 13,677
Problem with slaved axis
So I've been cutting with my Mechmate for a few years now and everything has been going great. Then last week without any warning, the slaved x(a) motor has started frequently (bot not always) going...
|
Forum: MechMates already cutting
Thu 19 September 2013, 08:10
|
Replies: 75
Views: 79,507
If you mirror those tarot cuts and roll ink on...
If you mirror those tarot cuts and roll ink on them, you have a nice set of printing blocks. I've been doing a few of these lately and it works beautifully on the mechmate. I use Extira for mine...
|
Forum: MechMates already cutting
Mon 01 April 2013, 06:10
|
Replies: 24
Views: 26,773
|
Forum: MechMates already cutting
Tue 26 March 2013, 07:34
|
Replies: 24
Views: 26,773
My garage is really short because of a heating...
My garage is really short because of a heating duct running across the ceiling. It's maybe 74". I also have a taller mechmate because I designed the bed to be able to lower for larger blocks of foam....
|
Forum: MechMates already cutting
Wed 06 March 2013, 15:09
|
Replies: 24
Views: 26,773
|
Forum: MechMates already cutting
Wed 06 March 2013, 06:10
|
Replies: 24
Views: 26,773
I'm going to try the route of attaching a hard...
I'm going to try the route of attaching a hard pipe right above the rear of my machine on the ceiling. Attach a flexible tube to that and the z-car. I have the bracket for holding the dust collector...
|
Forum: MechMates already cutting
Tue 19 February 2013, 08:46
|
Replies: 24
Views: 26,773
|
Forum: MechMates already cutting
Mon 18 February 2013, 20:25
|
Replies: 24
Views: 26,773
|
Forum: MechMates already cutting
Mon 18 February 2013, 20:23
|
Replies: 24
Views: 26,773
More dust than I know what to do with, to be...
More dust than I know what to do with, to be honest. I'm working on getting a dust collection system working in the very near future. It's a bit challenging with the very low ceiling that I'm working...
|
Forum: MechMates already cutting
Mon 18 February 2013, 19:08
|
Replies: 24
Views: 26,773
|
Forum: Cutting various materials - bit selection, feeds, speeds
Wed 26 September 2012, 08:24
|
Replies: 4
Views: 10,660
|
Forum: Cutting various materials - bit selection, feeds, speeds
Mon 11 April 2011, 10:23
|
Replies: 6
Views: 14,729
Just to put my 2 cents in, everyone, please...
Just to put my 2 cents in, everyone, please follow the advice about learning about the material safety for each of these products. I used to do foam carving and hardcoating for a living until the...
|
Forum: 702. Power Supplies
Thu 10 February 2011, 09:50
|
Replies: 10
Views: 15,652
|
Forum: 702. Power Supplies
Thu 10 February 2011, 07:54
|
Replies: 10
Views: 15,652
|
Forum: 702. Power Supplies
Wed 09 February 2011, 19:28
|
Replies: 10
Views: 15,652
I'm using the following setup that seems so...
I'm using the following setup that seems so popular.
4-PMDX-122
4-G203V
4-PK296B2A-SG7.2
My issue isn't so much about understanding the power supply circuit, but about the transformers...
|
Forum: 702. Power Supplies
Wed 09 February 2011, 11:06
|
Replies: 10
Views: 15,652
|