MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 4 of 4
Search took
0.00
seconds.
Search:
Posts Made By:
darren salyer
Forum:
10. Base Table
Sun 12 May 2013, 08:51
Replies:
13
what type of bleeder board to use?
Views:
20,655
Posted By
darren salyer
Trupan is merely a brandname for Ultralight...
Trupan is merely a brandname for Ultralight Medium Density Fiberboard. Any brand of Ultralight MDF should work fine, it has less density which is what makes it lighter, thereby being more porous.
Forum:
10. Base Table
Sun 12 May 2013, 08:49
Replies:
13
what type of bleeder board to use?
Views:
20,655
Posted By
darren salyer
If you build to the "blackbox" plans or similar,...
If you build to the "blackbox" plans or similar, I'd say Yes, that will work fine.
Its hard to believe the vacuum will go through a full sheet, but it was a "Holy Cow" moment for me the first time I...
Forum:
10. Base Table
Sun 12 May 2013, 07:01
Replies:
13
what type of bleeder board to use?
Views:
20,655
Posted By
darren salyer
I have a piece of 3/4" Trupan that I machined a...
I have a piece of 3/4" Trupan that I machined a 1/2" x 3/8" deep grid in, leaving 1" squares intact. It is installed on my table grid side down over the vac hole in the table. My work piece goes...
Forum:
10. Base Table
Sat 11 May 2013, 07:00
Replies:
13
what type of bleeder board to use?
Views:
20,655
Posted By
darren salyer
I went a much simpler direction. One 3" port...
I went a much simpler direction.
One 3" port through my table, under my 4x8 vacuum plenum board. When I need to hold a smaller part, I mask off the rest of the plenum board with some 1/4" UV coated...
Showing results 1 to 4 of 4
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
13:54
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.