MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Search
Today's Posts
Mark Forums Read
Showing results 1 to 14 of 14
Search took
0.00
seconds.
Search:
Posts Made By:
skippy
Forum:
MechMates already cutting
Mon 07 February 2011, 19:25
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Kangaroos can writeoff a car and still hop off...
Kangaroos can writeoff a car and still hop off into the bushes.
Forum:
MechMates already cutting
Sat 01 January 2011, 00:39
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Ross Yes it triggered Mach3 input with the...
Ross
Yes it triggered Mach3 input with the LED and resistor in the circuit.
With the flow sensor we installed now as we have added the glycol to the DI water and it make a mess if we add it...
Forum:
MechMates already cutting
Fri 31 December 2010, 22:08
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Ross The LED and 75 ohm resistor are...
Ross
The LED and 75 ohm resistor are connected is series to the touch probe circuit
Forum:
MechMates already cutting
Sun 28 November 2010, 03:57
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Sean Don't worry we have will be wiring the...
Sean
Don't worry we have will be wiring the E-Stop on the control box to turn the following power off Gecko, BOB's and VFD power but still let the computer run. So we can run the Computer running...
Forum:
MechMates already cutting
Mon 08 November 2010, 22:11
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Hi PEU as we are planning on running an indexer...
Hi PEU as we are planning on running an indexer and the BOB's only support 4 motors plus I/O in standard mode. We decide to use two BOB's. You only need the secound parallel port if you as doing the...
Forum:
MechMates already cutting
Thu 14 October 2010, 02:56
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
What I intend to do is rigid pipe in the brackets...
What I intend to do is rigid pipe in the brackets and a short length of flexible between the bottom of the rigid pipe to the dust foot at is attached to the spindle that way we only need to change a...
Forum:
MechMates already cutting
Mon 17 May 2010, 03:55
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Is it a case of Rum or is it case of shims
Here is the backup plan for the shims we hope not, but we will enjoy then after a day of build the MechMates
Regards
Paul
Forum:
MechMates already cutting
Fri 07 May 2010, 06:35
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Come on Guys new grinder has been purchase and I...
Come on Guys new grinder has been purchase and I have it (Been in the boot of my car for last coupe of days) and will be handed over to Tony tomorrow and the other one will be take back to shop for...
Forum:
MechMates already cutting
Sun 31 January 2010, 02:47
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Just saw the pics it must be great to have the...
Just saw the pics it must be great to have the right tools for the job. looks like we may need to start welding soon.
Forum:
MechMates already cutting
Thu 21 January 2010, 05:03
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Now that's why you wasn't home today.:D
Now that's why you wasn't home today.:D
Forum:
MechMates already cutting
Thu 21 January 2010, 03:23
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Now that's why you wasn't home today.:D
Now that's why you wasn't home today.:D
Forum:
MechMates already cutting
Tue 19 January 2010, 05:00
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
I thought the gecko keyring was was going to open...
I thought the gecko keyring was was going to open bottles as well. The only way I can see that it does it is between the hind leg and the tail all depending of what it is made of.
Regards
Paul
Forum:
MechMates already cutting
Tue 19 January 2010, 04:56
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Tony Looking good! Where is my gecko key ring?...
Tony
Looking good! Where is my gecko key ring? ;)
Regards
Paul
Forum:
MechMates already cutting
Tue 18 August 2009, 05:34
Replies:
440
Making Bar Signs! #71 - Brisbane, Australia
Views:
830,037
Posted By
skippy
Tony Rick's laser cut parts look ready good,...
Tony
Rick's laser cut parts look ready good, I see that he packed the same way that he sent them to me Which was great. Looks like that we got the new roller skate version, I might need to use...
Showing results 1 to 14 of 14
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
11:21
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.