MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Search
Today's Posts
Mark Forums Read
Showing results 1 to 14 of 14
Search took
0.00
seconds.
Search:
Posts Made By:
MetalHead
Forum:
Construction started, but not cutting yet
Mon 20 November 2017, 09:14
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Just so I understand. These motors move X & Y...
Just so I understand. These motors move X & Y just fine?
Forum:
Construction started, but not cutting yet
Sun 19 November 2017, 19:20
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
So are you saying you got your motors and still...
So are you saying you got your motors and still have an issue?
Forum:
Construction started, but not cutting yet
Sun 12 November 2017, 14:16
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
What voltage are you running at the motors?
What voltage are you running at the motors?
Forum:
Construction started, but not cutting yet
Sun 12 November 2017, 07:25
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Do you have a degaussing coil? ...
Do you have a degaussing coil?
http://www.cnczone.com/forums/general-cnc-machine-related-electronics/3848-scrap-steppers-servos-quickly.html
Post #9 was interesting about remagnetization.
...
Forum:
Construction started, but not cutting yet
Fri 10 November 2017, 16:40
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
I may have missed it in the threads, but have you...
I may have missed it in the threads, but have you looked at your Geckos? Also check the resistance of the limit resistor on the Gecko. Also try switching Gecko's and then the PMDX 133's. If this...
Forum:
Construction started, but not cutting yet
Tue 31 October 2017, 19:08
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
One thing folks should keep in mind, just like on...
One thing folks should keep in mind, just like on cars, over time and with use these dampeners wear out.
Forum:
Construction started, but not cutting yet
Tue 31 October 2017, 04:24
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Have you checked your spring dampeners to make...
Have you checked your spring dampeners to make sure they are ok? Does the motor work ok off of the machine? Sounds like if this is on your Z axis only your lift cylinders may need replacing.
Forum:
Construction started, but not cutting yet
Mon 16 November 2015, 04:59
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Hell of a grinder stand :) !! Looks great!!
Hell of a grinder stand :) !!
Looks great!!
Forum:
Construction started, but not cutting yet
Sun 01 November 2015, 04:19
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Your build is looking great !!!
Your build is looking great !!!
Forum:
Construction started, but not cutting yet
Mon 11 May 2015, 04:41
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Call Helukabel and ask if that cable is CNC...
Call Helukabel and ask if that cable is CNC rated. I always find if your cheap in the wire department it usually comes back to haunt you at some point sooner than later !!!
Forum:
Construction started, but not cutting yet
Tue 05 May 2015, 04:33
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
You need one that is not "momentary" - G is...
You need one that is not "momentary" - G is correct in the next post as usual :) - I miss read the specs when I reviewed that one !!
Forum:
Construction started, but not cutting yet
Fri 24 April 2015, 04:02
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
I am back - sent you a PM
I am back - sent you a PM
Forum:
Construction started, but not cutting yet
Sun 12 April 2015, 05:54
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Ok, Your over thinking your setup. Go read...
Ok,
Your over thinking your setup. Go read Rusty Nuts thread. http://www.mechmate.com/forums/showthread.php?t=3426
You should use the same motors across the machine for simplicity.
...
Forum:
Construction started, but not cutting yet
Sun 29 March 2015, 19:23
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,205
Posted By
MetalHead
Welcome aboard . As far as the build, get your...
Welcome aboard . As far as the build, get your size (6x12 I think you said) then build the machine direct drive to get it going . Use a basic control box design and spend your money up front on a...
Showing results 1 to 14 of 14
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
05:30
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.