MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Reload this Page Search Results
Register Options Profile Last 1 | 3 | 7 Days Today's Posts

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: dragonfinder1
Forum: MechMates already cutting Mon 01 August 2011, 08:29
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Kobus Maybe this has already been covered,...

Kobus

Maybe this has already been covered, if you plan to visit more than two National Parks ( there are 6 or 7 near Moab ) you should get a yearly pass. It costs about $50 (USD), otherwise it...
Forum: MechMates already cutting Mon 02 August 2010, 07:46
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
I've changed several chucks on Milwuaukee and...

I've changed several chucks on Milwuaukee and Dewalt drills and the screw that holds the chuck on is left handed and the chuck is right handed. I've never broken the screw, but they usually have lock...
Forum: MechMates already cutting Tue 13 July 2010, 07:03
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Marius Here in the U.S., if we do some work...

Marius

Here in the U.S., if we do some work for someone and they don't pay, we can put a labor lien against the property. They have to clear all the liens before they can sell the property. If you...
Forum: MechMates already cutting Fri 12 March 2010, 20:27
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
I have small boards on each side of the spoils...

I have small boards on each side of the spoils board, helps keep the chips off the floor and easier to clean up. I don't normally run the dust collector when I'm using v-bit cutters, they don't make...
Forum: MechMates already cutting Mon 15 February 2010, 09:19
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Kobus You use VcarvePro, but do you also...

Kobus

You use VcarvePro, but do you also have Cut3D? I wonder what more can be done with Cut3d.


Dave
Forum: MechMates already cutting Thu 14 January 2010, 10:25
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Actually I believe the ratio is still close to...

Actually I believe the ratio is still close to 3:1 with that gear. For me 24" ( 610 mm ) is 152 teeth. I think the problem is when the work is not the same size as the gear, and I think that is what...
Forum: MechMates already cutting Wed 13 January 2010, 14:37
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Here is a gear form Rush gears. It's 8.1"...

Here is a gear form Rush gears. It's 8.1" Diameter 160 tooth. Would that be large enough? 8:1 ratio direct and 24:1 with a 3:1 transmission, that should easily break a 12mm shaft :)
...
Forum: MechMates already cutting Wed 01 April 2009, 14:28
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Kobus Your neighbors must not like bikers,...

Kobus

Your neighbors must not like bikers, they all have high fences, doesn't look like you have any.

Just kidding, April 1st you know.
Forum: MechMates already cutting Thu 22 January 2009, 20:23
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
What does the clock look like now?

Kobus

Two questions 1: What does the clock that you were working on look like now? and 2: How you doing on the kiln for the glass?

Dave
Forum: MechMates already cutting Mon 13 October 2008, 21:11
Replies: 1,586
Views: 1,026,760
Posted By dragonfinder1
Kobus I don't see in your build thread what...

Kobus
I don't see in your build thread what size of power supply you ended up with for your MotionKing motors. I was going to use the Keling KL34H26-60-4A, but it looks like they are only 4 wire...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -6. The time now is 23:00.

Contact Us - www.mechmate.com - Archive - Top

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.