Forum: MechMates already cutting
Sat 01 November 2014, 10:33
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Thu 02 October 2014, 18:09
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Fri 16 May 2014, 15:38
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Tue 28 May 2013, 20:42
|
Replies: 518
Views: 322,314
Ok. That is just plain awesome in it's simple...
Ok. That is just plain awesome in it's simple perfection. Wish I'd finished my MM before my youngest was already walking. Which was years after my oldest walked straight into my shop at 4 years...
|
Forum: MechMates already cutting
Wed 12 January 2011, 17:53
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Fri 22 October 2010, 13:08
|
Replies: 518
Views: 322,314
Heath, I may not be. The computers in question...
Heath, I may not be. The computers in question (http://http://www.editcorp.com/Links/Gallery/HP2000.html) were over ten years old when I was first exposed to them in my pre-teens, and still in...
|
Forum: MechMates already cutting
Fri 22 October 2010, 12:10
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Fri 22 October 2010, 05:52
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Fri 13 August 2010, 11:39
|
Replies: 518
Views: 322,314
Forgive me for this, Russell, but ...
Six...
Forgive me for this, Russell, but ...
Six modest size holes in the floor oughta take care of that for ya! ;)
I have to load over the rail, due to limited space. My spoil is at around 32"; the...
|
Forum: MechMates already cutting
Thu 15 July 2010, 20:24
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Sat 10 April 2010, 12:38
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Sat 10 April 2010, 10:57
|
Replies: 518
Views: 322,314
Start from upper right, the unlabeled power...
Start from upper right, the unlabeled power conductor, which should be either L2 or N. It runs through a fuse, and to pin 1 of the contactor, labeled L1. It doesn't run anywhere else, like to the...
|
Forum: MechMates already cutting
Sat 10 April 2010, 09:22
|
Replies: 518
Views: 322,314
Hey, please note that the schematic in post #61...
Hey, please note that the schematic in post #61 has many problems. Start by tracing the power feeds in, and see that l1 goes to N on the contactor, and vice-versa. The control circuit and the power...
|
Forum: MechMates already cutting
Fri 09 April 2010, 21:48
|
Replies: 518
Views: 322,314
|
Forum: MechMates already cutting
Tue 02 February 2010, 19:23
|
Replies: 518
Views: 322,314
Thanks, Russell, that's useful information. Was...
Thanks, Russell, that's useful information. Was it easy to break apart? I'm wondering if in the case of attaching the rack, where the forces should be primarily along the long axis of the rack, the...
|
Forum: MechMates already cutting
Tue 02 February 2010, 17:52
|
Replies: 518
Views: 322,314
|