MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 8 of 8
Search took
0.00
seconds.
Search:
Posts Made By:
bradm
Forum:
MechMates already cutting
Fri 06 August 2010, 05:41
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
Ross, the one nice advantage of the suction side...
Ross, the one nice advantage of the suction side is that heavy items - like lost screws - are removed from the airstream before they can smack into the impeller.
Also, depending on your dust...
Forum:
MechMates already cutting
Tue 23 March 2010, 11:50
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
Heh. Very low tap water pressure is often much...
Heh. Very low tap water pressure is often much higher than what you'll get from a working pump. Plumb it up and see if you get any flow out of the other side. Almost anything beyond a trickle will...
Forum:
MechMates already cutting
Tue 23 March 2010, 08:39
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
Does the pump work when not connected to the...
Does the pump work when not connected to the spindle?
Forum:
MechMates already cutting
Mon 22 March 2010, 05:38
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
Yes, you can connect the shield of the wire...
Yes, you can connect the shield of the wire inside the box to a pin, and connect that pin to the shield of the wire outside the box. You can also connect those to the body of the connector itself,...
Forum:
MechMates already cutting
Fri 27 November 2009, 11:25
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
Ken, I haven't bothered to strip my EMC systems...
Ken, I haven't bothered to strip my EMC systems down, because they're fast enough to support the 500 IPM or so rapids on my MM. So I still have the network running, etc.
I could probably reduce...
Forum:
MechMates already cutting
Tue 24 November 2009, 09:38
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
EMC2 requires a linux kernel with real time...
EMC2 requires a linux kernel with real time extensions. This kernel is available as a pre-packaged option in the Ubuntu distribution. The EMC-Live disk is an Ubuntu release with the real time...
Forum:
MechMates already cutting
Mon 16 November 2009, 08:10
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
I'd try to keep the motherboard as far from the...
I'd try to keep the motherboard as far from the drives as possible, so something like choice 2 or 3, but with the motherboard mounted low down on the back of the door.
I think that mounting items...
Forum:
MechMates already cutting
Fri 13 November 2009, 22:27
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,922
Posted By
bradm
A checksum error after the battery replacement...
A checksum error after the battery replacement isn't unusual. If there is a bios 'reset to defaults' option, this is a good time to hit it. Hopefully after that, you can reboot, set your bios...
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
17:54
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.