MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 13 of 13
Search took
0.00
seconds.
Search:
Posts Made By:
bradm
Forum:
CNC motion control software
Tue 17 October 2017, 08:36
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Hey, glad you got it sorted!
Hey, glad you got it sorted!
Forum:
CNC motion control software
Sun 15 October 2017, 10:55
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Hmm. I'm fairly suspicious of those negative...
Hmm. I'm fairly suspicious of those negative axis limits confusing things. I would have expected MIN_LIMIT = 0, MAXLIMIT = (1200, 700, 120), HOME_OFFSET = (1199.75, 699.75, 119.75)
Forum:
CNC motion control software
Sat 14 October 2017, 08:43
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Okay, that's all really weird. Can you post or...
Okay, that's all really weird. Can you post or PM me your .ini file so I can go through it?
Forum:
CNC motion control software
Fri 13 October 2017, 08:30
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
So, what are your machine limits? Which limit...
So, what are your machine limits? Which limit was exceeded? Z? I'm guessing that because of the red box at the lower limit of the Z axis on the display, and because you were apparently happy with...
Forum:
CNC motion control software
Thu 12 October 2017, 06:51
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Hmm. I haven't seen that. For the "no...
Hmm. I haven't seen that. For the "no percent", try making sure there is a blank line at the end of the file, after the percent. If there is no line ending, it may not be seeing the percent...
Forum:
CNC motion control software
Wed 11 October 2017, 19:05
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Yes, "X" means the X key on the keyboard - same...
Yes, "X" means the X key on the keyboard - same for all the others. And yes, if you have the cross hair over your 0,0 then "X" "End" <offset> "Enter" and "Y" "End" <offset> "Enter" sets up your...
Forum:
CNC motion control software
Tue 10 October 2017, 06:49
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Yeah, there's some not super helpful info around,...
Yeah, there's some not super helpful info around, like http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Homing_And_Limit_Switch but first you need to be comfortable with editing the config files.
I'm not...
Forum:
CNC motion control software
Tue 03 October 2017, 12:59
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Not much has changed. However, this is really a...
Not much has changed. However, this is really a low risk operation, if you get the bootable image (http://linuxcnc.org/docs/2.7/html/getting-started/getting-linuxcnc.html) and fire it up. No...
Forum:
CNC motion control software
Tue 29 December 2009, 11:23
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Orotemo, you may have stumped me. You could try...
Orotemo, you may have stumped me. You could try the #emc irc channel (on freenode.net).
However, if you have separate home and limits, you could consider placing all the homes together with pin...
Forum:
CNC motion control software
Sun 27 December 2009, 06:16
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
Note: I use EMC2, with a single limit switch on...
Note: I use EMC2, with a single limit switch on one of the two gantry motors. In practice, the only time it gets out of square is if there is a crash, in which case I use the hard stops to realign....
Forum:
CNC motion control software
Sat 29 November 2008, 09:48
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
As Gerald discovered, the EMC / Ubuntu CD can be...
As Gerald discovered, the EMC / Ubuntu CD can be found at:
http://www.linuxcnc.org/content/view/21/4/lang,en/
Most variants / derivatives of Ubuntu come in a live CD version that can be booted...
Forum:
CNC motion control software
Sat 29 November 2008, 07:41
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
The initial step is to boot the linux CD. There...
The initial step is to boot the linux CD. There is then an option to install it to your hard drive. During that process, you can choose to set up your system as a dual boot setup, where you chose...
Forum:
CNC motion control software
Mon 17 November 2008, 06:35
Replies:
62
Setting up EMC2
Views:
73,909
Posted By
bradm
If anyone wants help with EMC2, just give me a...
If anyone wants help with EMC2, just give me a shout. I'm running it on my MechMate, on my benchtop mill, and I've been working with Linux systems since 1992 or so.
Showing results 1 to 13 of 13
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
11:54
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.