Forum: Introduce yourself and start planning
Wed 02 March 2016, 06:32
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 29 February 2016, 09:56
|
Replies: 37
Views: 38,713
Guys,
While waiting for more parts to...
Guys,
While waiting for more parts to arrive, I tried to design my reduction pulley system.
It seems like the combination of my 34HS9801 motor with 25mm HTD pulley will cause about 17mm of the...
|
Forum: Introduce yourself and start planning
Wed 17 February 2016, 11:28
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 15 February 2016, 21:45
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 15 February 2016, 06:27
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 15 February 2016, 00:23
|
Replies: 37
Views: 38,713
Thanks Sean and Tom. I will keep the extra.
...
Thanks Sean and Tom. I will keep the extra.
Need one more help... need to figure out specs for reduction belts/pulleys.
I think I'm going with the GT2/GT3 profile as it's designed for high...
|
Forum: Introduce yourself and start planning
Sun 14 February 2016, 05:20
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Sun 14 February 2016, 03:43
|
Replies: 37
Views: 38,713
Received gas struts and transformer from RS.
...
Received gas struts and transformer from RS.
It's bigger than I imagined.
I know they're 880mm long (400mm stroke), and it'll protrude vertically quite tall, but didn't imagined it would be...
|
Forum: Introduce yourself and start planning
Thu 11 February 2016, 05:01
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 08 February 2016, 21:23
|
Replies: 37
Views: 38,713
It's 2016!
After 7 years, I'm reviving the...
It's 2016!
After 7 years, I'm reviving the project.
Took all the parts already purchased in 2008 out of my closet, still look brand new.
Some bearings have a bit of rust, going to ditch...
|
Forum: Introduce yourself and start planning
Thu 01 January 2009, 04:08
|
Replies: 37
Views: 38,713
Well i was confused, been thinking to much so...
Well i was confused, been thinking to much so that everything fits inside the budget bracket.
When i find that hardened chrome shaft is cheaper here than in the net, i was thinking that i might...
|
Forum: Introduce yourself and start planning
Thu 01 January 2009, 03:35
|
Replies: 37
Views: 38,713
i worry about that too... but weighing between...
i worry about that too... but weighing between cost and performance i'd go with the g540 first. If it fails me, i'll try to go the pulley reduction way (i will, eventually, anyway, for finer cuts....
|
Forum: Introduce yourself and start planning
Thu 01 January 2009, 02:44
|
Replies: 37
Views: 38,713
Ok ordered stepper motor and driver.
Driver...
Ok ordered stepper motor and driver.
Driver will arrive tomorrow.
Stepper will start shipping on the 5th due to long holiday in China.
Have sent drawings of V-Roller, ecc. bushings etc. to...
|
Forum: Introduce yourself and start planning
Mon 22 December 2008, 15:35
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 22 December 2008, 13:22
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Mon 22 December 2008, 13:10
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Sat 13 December 2008, 23:40
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Sat 13 December 2008, 16:55
|
Replies: 37
Views: 38,713
|
Forum: Introduce yourself and start planning
Sat 13 December 2008, 09:44
|
Replies: 37
Views: 38,713
MechMate Project in Johore, Malaysia.
Hi,
I've registered meself into this forum quite a long time ago, and now ready to get serious. Someone decided to donate around US$2000 for me to build one.
This thread will be a journal of my...
|