Forum: MechMates already cutting
Mon 23 December 2013, 22:08
|
Replies: 667
Views: 338,253
Pete,Yes I am pleased but there is a huge...
Pete,Yes I am pleased but there is a huge learning curve waiting.I need to sort out a couple of things still.( dead stops,some more motor tuning,get the z-axis square to the project it is cutting )...
|
Forum: MechMates already cutting
Sun 22 December 2013, 22:11
|
Replies: 667
Views: 338,253
my first test leg
So I had time to complete my stand alone lathe.After many wasted material this is what I came up with.I must say this is one huge challenge.
It also takes ages to turn so now it is time to figure...
|
Forum: MechMates already cutting
Mon 04 November 2013, 11:25
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Fri 01 November 2013, 02:16
|
Replies: 667
Views: 338,253
z-SLIDE DONE
My z-slide is done now to neaten up wiring and to start this baby up.
|
Forum: MechMates already cutting
Thu 17 October 2013, 18:43
|
Replies: 667
Views: 338,253
Danilo, yes I could have ordered one but the...
Danilo, yes I could have ordered one but the shipping cost to my side is more than the product itself .I got 2 sets of those brackets for R 300 .00 ( $30 for 2 sets ).to mill it out of alu would have...
|
Forum: MechMates already cutting
Thu 17 October 2013, 10:04
|
Replies: 667
Views: 338,253
laser cutting or plasma ?
I got my spindle mount brackets and fitted them to the spindle perfect fit.The question is which is better laser or plasma brackets are 16 mm thick steel
|
Forum: MechMates already cutting
Fri 11 October 2013, 10:52
|
Replies: 667
Views: 338,253
some more progress
I got the cable chain it sits where it should be limit switches are installed
|
Forum: MechMates already cutting
Fri 27 September 2013, 06:58
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Fri 27 September 2013, 06:54
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Fri 27 September 2013, 00:30
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Thu 26 September 2013, 22:26
|
Replies: 667
Views: 338,253
Alan I am still alive but why don`t you answer...
Alan I am still alive but why don`t you answer your phone!:confused:
I am busy assembling the lathe.I got my water cooled spindle last week last Hiwin bearings was delivered yesterday and it was...
|
Forum: MechMates already cutting
Thu 26 September 2013, 12:33
|
Replies: 667
Views: 338,253
Only with a Mechmate
I did these for a client recently Wine wall with 240 / 12 mm dia holes took 4 hours with a 6 mm cutter at 5 mm/sec feed rate.
Table legs thanks to MM.
|
Forum: MechMates already cutting
Tue 04 June 2013, 06:44
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Fri 08 March 2013, 00:51
|
Replies: 667
Views: 338,253
Progress on my Lathe project
Ok, so it has been a while since I did anything and the budget is not cooperating but I had to do something with what I had in the workshop.I started with my z-slide and gantry for the lathe.I did...
|
Forum: MechMates already cutting
Mon 29 October 2012, 05:07
|
Replies: 667
Views: 338,253
Alan it is a 3 axis.
Hi Johan, how are you...
Alan it is a 3 axis.
Hi Johan, how are you doing?
Duckie, Yes so far it is going to be but lets see if I can break it first.length of cut on the x-axis is 1220 mm and max dia of turning provided...
|
Forum: MechMates already cutting
Sat 27 October 2012, 22:12
|
Replies: 667
Views: 338,253
New lathe
Ok, What does one do when you get cleaned out.Most of my power tools have received new homes due to affirmative shopping and I am really "de moer in".Even Carolina`s fathers welding machine that I...
|
Forum: MechMates already cutting
Thu 04 October 2012, 10:23
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Thu 04 October 2012, 10:19
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Thu 04 October 2012, 10:12
|
Replies: 667
Views: 338,253
I got a quote from an engineering firm that...
I got a quote from an engineering firm that manufactures module 1 gears and what not.I didn`t know that a 30 teeth module 1 pinion gear would cost R 318.00 + 14 % vat. And a 180 teeth module 1 gear...
|
Forum: MechMates already cutting
Fri 24 August 2012, 22:03
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Fri 24 August 2012, 07:21
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Thu 23 August 2012, 11:58
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Thu 23 August 2012, 09:31
|
Replies: 667
Views: 338,253
Marius the distance of rack that I use will be...
Marius the distance of rack that I use will be about 50mm when I am cutting ( 2 d cutting 95 % of the time and even 3d cutting).Even if we let it go up to the max and down to the max we only cut max...
|
Forum: MechMates already cutting
Thu 23 August 2012, 08:59
|
Replies: 667
Views: 338,253
|
Forum: MechMates already cutting
Thu 23 August 2012, 05:22
|
Replies: 667
Views: 338,253
|